<
>
Specifications
Tolerance:
±5%
Voltage Rating:
450V
Capacitance:
150nF
Operating Temperature:
-40℃~+105℃
Dielectric Material:
Metallized Polypropylene
Mfr. Part #:
W372S154JK6L0090EC
Package:
Through Hole,P=10mm
Key Attributes
Model Number:
W372S154JK6L0090EC
Product Description
Product Overview
This document outlines the specifications for Metallized Polypropylene Film Capacitors. It details product structure, technical parameters, and testing procedures to ensure compliance with industry standards.
Product Attributes
- Brand: (Weidi)
- Origin: Shenzhen, China
- Material: Metallized Polypropylene Film
- Outer Encapsulation: Flame Retardant Epoxy Resin
Technical Specifications
| Parameter | Specification | Notes | ||
| Product Name | Metallized Polypropylene Film Capacitor | |||
| Product Structure | Metallized Polypropylene Film, Gold Spray Layer, Leads, Inner Encapsulation Epoxy Resin, Outer Encapsulation Flame Retardant Epoxy Resin | |||
| Atmospheric Conditions | Standard Atmospheric Conditions (255), (505)% RH, 86-106kPa | |||
| Reference Conditions | Temperature: 25, Humidity: (505)%, Pressure: 86-106kPa | |||
| Climatic Category | 40/125/21 | |||
| Rated Temperature | 125 | |||
| Operating Temperature Range | -40 ~ 125 | (Rated voltage: 125) | ||
| Rated Voltage | 50V, 100V, 250V, 400V, 630V, 1000V | |||
| Capacitance Range | 0.001F ~ 10F | (at 25, 1Vrms, 1kHz) | ||
| Capacitance Tolerance | 5% (J), 10% (K) | |||
| Withstand Voltage | 2.0 * Ur (5s) | Voltage application rate: 10V/s; Cut-off current: 50mA | ||
| Dissipation Factor (tan) | 0.001 (at 25, 1kHz) | |||
| Insulation Resistance | 10000M (C0.33F) | (at 25, 100Vdc, 60s) | ||
| 3000s (C0.33F) | (at 25, 100Vdc, 60s) | |||
| Lead Strength (Tensile) | Diameter (mm) | Tensile (N) | ||
| 0.8 | 20 | |||
| 0.8 | 50 | |||
| Lead Strength (Bending) | Diameter (mm) | Load (N) | Duration (s) | |
| 0.8 | 3 | 5 | Two bends in each of two directions | |
| 0.8 | 5 | 5 | Two bends in each of two directions | |
| No visible damage to leads after test | ||||
| Solderability | Soldering Pot Temp: 35010 | Immersion Time: 3s0.5s | Good tinning on lead surface | |
| Resistance to Soldering Heat | Soldering Pot Temp: 35010 | Immersion Time: 3s0.5s | Immersion depth: 1.5mm0.5mm from mounting surface, using 1.00.1mm insulating shield plate | |
| Capacitance Change: C/C0 2% | Dissipation Change: tan 0.001 | |||
| Rapid Temperature Change | Temp: 1 = -40; 2 = 125 | Duration: 30min | Cycles: 100 | |
| Capacitance Change: C/C0 3% | Dissipation Change: tan 0.002 | Insulation Resistance: Initial measurement value | ||
| Vibration | Frequency: 10-500-10Hz | Direction & Time: 3 directions, 2 hours each, total 6 hours | Amplitude or Acceleration: 1.5mm or 10g (whichever is lower) | |
| Product appearance without visible damage or looseness | ||||
| Impact | Impacts: 3 times | Acceleration: 100g | Pulse Duration: 6ms | |
| Product appearance without visible damage or looseness | ||||
| Sequential Climate Test (Dry Heat) | Temperature: 125 | Duration: 16 hours | Final Measurement: No permanent breakdown or flashover, appearance without visible damage, clear marking | |
| Capacitance Change: C/C0 5% | Dissipation Change: tan 0.005 | Insulation Resistance: Initial measurement value * 0.5 | ||
| Sequential Climate Test (Damp Heat) | Severity: 95% RH, 40 for 48 hours | First Cycle: Cold Temp: -40, Duration: 4 hours | Low Pressure: Temp: 25, Pressure: 10hPa, Duration: 4 hours | |
| (Rated voltage applied for the last 10 mins of the test cycle) | ||||
| Sequential Climate Test (Damp Heat) | Severity: 95% RH, 40 for 48 hours | Other Cycles: Complete other cycles | After test, apply rated voltage for 1 minute | |
| Steady State Damp Heat | Temperature: 402 | Humidity: 90-96% | Duration: 21 days | |
| Appearance without visible damage, clear marking; Capacitance Change: C/C0 5%; Dissipation Change: tan 0.005; Insulation Resistance: Initial measurement value * 0.5 |
2405081155_WEIDY-W372S154JK6L0090EC_C22378718.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
