<
>
Specifications
Lifetime:
5000hrs@105℃
Operating Temperature:
-40℃~+105℃
Capacitance:
10uF
Height - Seated (Max):
13mm
Pin Spacing:
5mm
Voltage Rating:
450V
Diameter:
10mm
Ripple Current:
85mA@120Hz
Tolerance:
±20%
Mfr. Part #:
KF2W100M1013EAH1C0LC
Package:
Through Hole,D10xL13mm
Key Attributes
Model Number:
KF2W100M1013EAH1C0LC
Product Description
Product Overview
This specification covers the KF series Radial Type Aluminum Electrolytic Capacitors from SICHUAN SINCERITY TECHNOLOGY CO., LTD. These capacitors are designed for various applications and adhere to JIS-C-5101 and JIC-C-5141 standards.
Product Attributes
- Brand: (Sincerity)
- Origin: Sichuan, China
- Manufacturer: SICHUAN SINCERITY TECHNOLOGY CO., LTD.
- Copyright: Sichuan Sincerity Technology Co., Ltd.
Technical Specifications
| Product number | Series | RATE VOLTAGE (V.DC) | Capacitance (uF) | Capacitance Tolerance (%) | DF tan (%) | MAX Leakage Current (uA) | Max. Ripple Current (mA) RMS at 105 120Hz | Impedance at 20 100KHz () | Load Life (Hours) | Temperature Range () | Surge Voltage (V.DC) | Dimensions (mm) D | Dimensions (mm) L |
| KF2W100M1013EAH1C0LC | KF | 450 | 10 | 20 | 20 | 115 | 85 | / | 5000 | -40+105 | 500 | 10 | 13 |
| KF2G4R7M0812DAH1C0LC | KF | 400 | 4.7 | 20 | 20 | 62.6 | 52 | / | 5000 | -40+105 | 450 | 8 | 12 |
| KF2G100M0816DAH1E0LC | KF | 400 | 10 | 20 | 20 | 105 | 82 | / | 5000 | -40+105 | 450 | 8 | 16 |
| KF2E100M0812DAH1C0LC | KF | 250 | 10 | 20 | 15 | 75 | 70 | / | 5000 | -40+105 | 300 | 8 | 12 |
General Specifications
| Parameter | Condition | Criteria |
| Capacitance | Measuring frequency: 120Hz 20% Measuring circuit: Series equivalent circuit Measuring voltage: 1Vrms | Capacitance tolerance: 20% |
| Dissipation Factor (tan) | Test conditions are the same as Capacitance | See Table 1 (WV: 160-500V, tg: 0.15-0.24) |
| Leakage Current | Rated voltage applied, 100010% protective resistor, measured after 2 min. | DC: 160~500V.DC, I0.02CV+25uA |
| High and Low Temperature Characteristic | Step 1: 202; Step 2: -25/-40-3+0 for 120min; Step 3: 202; Step 4: 105-0+3 for 120min. | Step 2: Impedance value compared to Step 1, not more than Table 2 requires. Step 4: Capacity value compared to Step 1, variation within 20%. |
| Surge Voltage Test | Apply surge voltage (Table 3), charge 305s, discharge 3305s for 1000 cycles. Test temp: 15~35. | Capacitance Change: Within 20% of initial value. Dissipation Factor: Not more than 200% of Table 1 specified value. Leakage Current: To satisfy No. 4.1.4. |
| Tensile strength of termination | At Room temperature, along the lead line down direction, apply tension for 51 seconds. | (Force values provided for wire diameters 0.45mm to 1.0mm) |
| Bending strength of termination | At Room temperature, apply fixed gravity to leads, bend body 90 degrees and return, repeat in opposite direction. Process completed in 5 seconds. | No intermittent contacts, open or short-circuiting. No visible mechanical damage. |
| Vibration | 3 orthogonal directions, 2h each (total 6h). Frequency: 10~55Hz. Amplitude: 1.5mm. Sweep rate: 10~55~10Hz in about 1 min. | No intermittent contacts, open or short-circuiting. No visible mechanical damage. |
| Solder ability Test | Solder temp: 2455. Dipping time: 20.5 s. | At least 90% of circumferential surface of the dipping portion of termination shall be covered with new solder. |
| Load Life Test | Test temp: 1052C, rated voltage and ripple current applied. Test time: 5000H. | Capacitance Change: Within 20% of initial value. Dissipation Factor: Not more than 200% of initial value. Leakage Current: To satisfy No. 4.1.4. Appearance: No remarkable abnormality. |
| Shelf Life Test | Stored at 1052 with no voltage applied for 1000-0+48h, then resumed 16 hours. | Capacitance Change: Within 20% of initial value. Dissipation Factor: Not more than 200% of initial value. Leakage Current: Not more than 200% of initial value. Appearance: No remarkable abnormality. |
| SolderHeatResistance | Solder Temp: 2605 C. Dipping time: 101 s. Printed wiring board: 1.6mm. | Capacitance Change: Within 10% of initial value. Dissipation Factor: Not more than the specified value. Leakage Current: To satisfy No. 4.1.4. Appearance: No remarkable abnormality. |
| Safety Vent | Applies to products with vent at diameter 8. Conditions vary by diameter (22.4mm or 22.5mm). | No explosion, flash, flame, spark or fire. No expulsion of metal from casing. |
| Resistance to damp heat | Test temp: 402C. Relative humidity: 90~95%. Test time: 5008h. After test, subject to standard atmospheric conditions for 1~2 hours. | Capacitance Change: Within 10% of initial value. |
2411121111_SRD-KF2W100M1013EAH1C0LC_C41430185.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
