Crystal Oscillator Series 6N
The 6N Series is a seam-sealed ceramic crystal oscillator in a 7.0x5.0mm surface mount package. It offers a stable and reliable frequency output for various electronic applications.
Product Attributes
- Brand: SJK ()
- Origin: Shenzhen, China
- Package: 7.0x5.0mm Surface Mount, Ceramic, Seam Sealed
- Certifications: RoHS, REACH, HF
- Moisture Sensitivity Level: Level 1
Technical Specifications
| Parameter | Symbol | Min | Type | Max | Units | Notes |
|---|---|---|---|---|---|---|
| Nominal Frequency | 16.000000 | MHZ | ||||
| Frequency Stability AT 25 | 10 | PPM | ||||
| Frequency Stability Over Operating Temperature range | 20 | PPM | -4085 | |||
| Operating Temperature | Topr | -40 | 25 | 85 | ||
| Storage Temperature | Tstg | -55 | 125 | |||
| Supply Voltage | VDD | 3.3 | V | 10% | ||
| Input Current | Icc | 5 | mA | |||
| Enable Control | Yes | Pad1 | ||||
| Output Load | CL | 15 | pF | CMOS | ||
| Output Voltage High | VoH | 90% | Vdd | |||
| Output Voltage Low | VoL | 10% | Vdd | |||
| Rise Time | Tr | 5 | ns | 10%90%VDD Level | ||
| Fall Time | Tf | 5 | ns | 90%10%VDD Level | ||
| Symmetry (Duty ratio) | TH/T | 45 | 55 | % | ||
| Start-up Time | Tosc | 10 | ms | |||
| Enable Voltage High | Vhi | 70% | Vdd | |||
| Disable Voltage Low | Vlo | 30% | Vdd | |||
| Aging | 3 | ppm/yr. | 1st. Year at 25 | |||
| Output Disable Delay Time | T off | 150 | us | |||
| Output Enable Delay Time | T on | 150 | us | |||
| Phase Jitter (12KHZ~20MHZ) | 0.5 | 1.0 | ps |
Dimensions
(Units :mm)
Marking
Test Circuit
Control input (output enable/disable) Logic 1 or open on pad 1: Oscillator output
Logic 0 on pad 1 : Disable output to high impedance
Waveform Conditions
Output Enable / Disable Delay
The oscillator timing during normal operation is shown in the figures. When the device is in standby, the oscillator stops. When standby is released, the oscillator starts and stable oscillator output occurs after a short delay.
Suggested Reflow Profile
Total time : 200 sec. Max / Solder melting point :220
Waveform measurement system should have a min. bandwidth of 5 times the frequency being tested.
Reliability Test Specification
Mechanical Endurance
| No. | Test Item | Test Methods | REF. DOC |
|---|---|---|---|
| 1 | Drop Test | 75 cm height,3 times on concrete floor . | JIS C6701 |
| 2 | Mechanical Shock | Device are shocked to half sine wave ( 1000 G ) three mutually perpendicular axes each 3 times. 0.5m sec. duration time | MIL-STD-202F |
| 3 | Vibration | Frequency range 10 ~ 2000 Hz Amplitude 1.52 mm/20G Sweep time 20 minutes Perpendicular axes each test time 4 Hrs (Total test time 12 Hrs) | MIL-STD-883E |
| 4 | Gross Leak | Standard Sample For Automatic Gross Leak Detector, Test Pressure: 2kg / cm2 | MIL-STD-883E |
| 5 | Fine Leak | Helium Bomging 4.5 kgf / cm 2 for 2 Hrs | |
| 6 | Solderability | Temperature 245 5 Immersing depth 0.5 mm minimum Immersion time 5 1 seconds Flux Rosin resin methyl alcohol solvent ( 1 : 4 ) | MIL-STD-883E |
Environmental Endurance
| No. | Test Item | Test Methods | REF. DOC |
|---|---|---|---|
| 1 | Resistance To Soldering Heat | Pre-heat temperature 125 Pre-heat time 60 ~ 120 sec. Test temperature 260 5 Test time 10 1 sec. | MIL-STD-202F |
| 2 | High Temp. Storage | + 125 3 for 1000 12Hrs | MIL-STD-883E |
| 3 | Low Temp. Storage | - 40 3 for 1000 12Hrs | MIL-STD-883E |
| 4 | Thermal Shock | Total 100 cycles of the following temperature cycle | MIL-STD-883E |
| 5 | Pressure Cooker Storage | 121 3 , RH100% , 2 bar , 240Hrs | JIS C6701 |
| 6 | High Temp Humidity | 85 3, RH 85% , 1000Hrs | JIS C5023 |
2207271530_SJK-6N16000G33YC_C252381.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
