Product Overview
This document specifies the Approval Specification for Metal Current Sensing Chip Resistors, Type HI XD. These resistors offer high power capabilities up to 3W, low TCR down to 50ppm/, and are suitable for reflow and wave soldering. They feature halogen-free epoxy, lead-free plating, superior mechanical strength, and excellent high-frequency characteristics, complying with RoHS standards.
Product Attributes
- Brand: Changzhou Pengke Electronics
- Origin: China
- Material: Metal Alloy Resistance
- Certifications: RoHS compliant
Technical Specifications
| Product Category | Rated Power | Resistance Range | TCR | Operating Temperature Range | Resistance Tolerance | Insulation Resistance | Max. Operating Voltage (V) |
| 2512 DD/XD | 2W/3W | 0mR 1m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1m<R 2m | 100ppm/ | ||||||
| 2m<R 500m | 50 ppm/ | ||||||
| 1206 RC | 1W | 0mR 2m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 2m<R 200m | 50 ppm/ | ||||||
| 0805 RE | 0.5W | 5mR 15m | 50ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
Construction and Dimension (mm)
| Category | L | W | T | A |
| 2512 | 6.40.20 | 3.20.20 | 0.80.20 | DD:2.00.20 (R4 m) XD:1.00.20 (R0.5 m) |
| 1206 | 3.20.20 | 1.60.20 | 0.70.20 | 0m R<10m 0.60.20 |
| 10m<R 200m 0.450.20 | ||||
| 0805 | 2.00.10 | 1.250.10 | 0.50.20 | 0.350.20 |
Land Pattern Dimensions (mm)
| Category | a | b | L |
| 0805 RE | 1.5 | 1 | 1 |
| 1206 RC | 1.8 | 1.7 | 1.6 |
| 2512 XD | 4 | 2.1 | 4.1 |
| 2512 DD | 4 | 3.1 | 1.3 |
Reliability Tests
| Project | Test Method | Specifications and Requirements |
| Temperature coefficient (TCR) | Measured at 25(T1, R1) and 125(T2, R2) | Refer to TCR specifications for physical features |
| Short Time Overload | 5 times rated power, maintain 5s | R 1%+0.05m |
| Insulation resistance | Apply 100V15V DC voltage between electrode and substrate, hold for 60 seconds, then measure insulation resistance | > 100 M |
| Withstand voltage | AC voltage of maximum overload voltage applied between electrode and substrate at approx. 100V/S, holding 605s | No breakdown or arc |
| Solderability | 2455 tin tank, hold 2s0.5s | At least 95% of surface area of electrode shall be covered with new solder |
| Resistance to Soldering Heat | 2605 tin tank, hold for 10s1s | R (0.5%+0.05m ), no visible damage |
| Bending test | Bending distance 2mm, hold time 60s5s | R0.5%+0.05m , no mechanical damage |
| Solvent resistance | Isopropanol (IPA) at 235 for 10 hours | No obvious damage to appearance |
| High Temperature Exposure | 1702, 1000H | R (1.0%+0.05m ) |
| Low Temperature Exposure | -552, 1000H | R (0.5%+0.05m ) |
| Rapid change of Temperature | -55 30 min ~ normal temp 5 min ~155 30 min, 1000 cycles | R (0.5%+0.05m ) |
| Load Life | 702, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m ) |
| Moisture with Load | 852, 85%3%RH, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m) |
Tape Packaging Dimensions (mm)
| Type | A | B | C | D | E | T1 | T2 |
| 0805 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.01 | / |
| 1206 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.00.3 | 11.4 1.0 |
| 2512 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 13.0 0.3 | 15.4 1.0 |
Reel Dimensions (mm)
| Type | D | C | E | T1 |
| 0805 | 1782.0 | 601.0 | 131.0 | 9.01 |
| 1206 | 1782.0 | 601.0 | 131.0 | 9.00.3 |
| 2512 | 1782.0 | 601.0 | 131.0 | 13.0 0.3 |
Label Information
Packaging Quantity: 0805/1206: 5000pcs/Reel, 2512: 4000pcs/Reel. Labels shall be marked with: (1) Size, (2) Quantity, (3) LOT.NO., (4) Manufacturers name.
Recommended Reflow Soldering Profile
Solder: Sn96.5 / Ag3 / Cu0.5. Peak Temperature: 240~260, 10 sec. Pre-heating Zone: 150 to 200 , 9030 sec. Soldering Zone: 230 or higher, 3010 sec.
Care Note for Storage
Storage conditions: Temperature 535, Relative Humidity 4575% RH. Avoid direct sunlight, moisture, dust, and harmful gases (Hydrogen chloride, sulfurous acid gas, Hydrogen sulfide). Storage life: 1 year.
Care Note for Operating and Handling
Avoid exceeding normal rated power. Handle with care using tweezers to prevent damage to the protective layer or resistance body. Do not touch the product with the soldering tip during manual installation.
2509261615_RVR-HIXD25LR0025F_C52015886.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
