Product Overview
This document specifies the approval specifications for Metal Current Sensing Chip Resistors, Type 2512/1206/0805 series. These resistors offer high power up to 3W, low TCR as 50ppm/, and are suitable for reflow and wave soldering. They feature Halogen Free Epoxy, Lead Free Plating, superior mechanical strength, and excellent high-frequency characteristics, complying with RoHS standards.
Product Attributes
- Brand: Changzhou Pengke Electronics
- Origin: China
- Material: Metal Alloy
- Certifications: RoHS compliant
Technical Specifications
| Category | Model | Rated Power | Resistance Range | TCR | Operating Temp Range | Resistance Tolerance | Insulation Resistance | Max Operating Voltage (V) |
| 2512 DD/XD | 2512 | 2W/3W | 0mR 1m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1m<R 2m | 100ppm/ | |||||||
| 2512 DD/XD | 2512 | 2W/3W | 2m<R 500m | 50 ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1206 RC | 1206 | 1W | 0mR 2m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1206 | 1W | 2m<R 200m | 50 ppm/ | |||||
| 0805 RE | 0805 | 0.5W | 5mR 15m | 50ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
Construction and Dimension
| Category | L (mm) | W (mm) | T (mm) | A (mm) |
| 2512 | 6.40.20 | 3.20.20 | 0.80.20 | DD:2.00.20 (R4 m) XD:1.00.20 (R0.5 m) |
| 1206 | 3.20.20 | 1.60.20 | 0.70.20 (0m R<10m) 0.450.20 (10m<R 200m) | 0.60.20 |
| 0805 | 2.00.10 | 1.250.10 | 0.50.20 | 0.350.20 |
Land Pattern Dimensions
| Category | a (mm) | b (mm) | L (mm) |
| 0805 RE | 1.5 | 1 | 1 |
| 1206 RC | 1.8 | 1.7 | 1.6 |
| 2512 XD | 4 | 2.1 | 4.1 |
| 2512 DD | 4 | 3.1 | 1.3 |
Reliability Tests
| Project | Test Method | Specifications and Requirements |
| Temperature coefficient (TCR) | Resistance values were measured at 25(T1, R1) and 125(T2, R2), and TCR was calculated as (R2-R1)/ (R1 (T2-T1)) *10^6 | Refer to TCR specifications for physical features |
| Short Time Overload | 5 times rated power, maintain 5s | R 1%+0.05m |
| Insulation resistance | Apply 100V15V DC voltage between electrode and substrate, hold for 60 seconds, then measure insulation resistance | > 100 M |
| Withstand voltage | An alternating current with an effective value of the maximum overload voltage is applied between the electrode and the substrate at a rate of approximately 100V/S, maintaining 605s | No breakdown or arc |
| Solderability | 2455 tin tank, hold 2s0.5s | At least 95% of surface area of electrode shall be covered with new solder |
| Resistance to Soldering Heat | 2605 tin tank, hold for 10s1s | R (0.5%+0.05m ), no visible damage |
| Bending test | Bending distance 2mm, hold time 60s5s | R0.5%+0.05m , no mechanical damage |
| Solvent resistance | Isopropanol (IPA) at 235 for 10 hours | No obvious damage to appearance |
| High Temperature Exposure | 1702, 1000H, stand for 1H, test the resistance value | R (1.0%+0.05m ) |
| Low Temperature Exposure | -552, 1000H, stand for 1H, test the resistance value | R (0.5%+0.05m ) |
| Rapid change of Temperature | -55 30 minutes ~ normal temperature 5 minutes ~155 30 minutes, 1000 cycles | R (0.5%+0.05m ) |
| Load Life | 702, 1000 hours, rated power 1.5 hours on / 0.5 hours off | R (1.0%+0.05m ) |
| Moisture with Load | 852, 85%3%RH, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m) |
Tape Packaging Dimensions
| Type | A (mm) | B (mm) | C (mm) | D (mm) | E (mm) | T1 (mm) | T2 (mm) |
| 0805 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.01 | / |
| 1206 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.00.3 | 11.4 1.0 |
| 2512 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 13.0 0.3 | 15.4 1.0 |
Reel Dimensions
| D (mm) | C (mm) | E (mm) | T1 (mm) |
| 1782.0 | 601.0 | 131.0 | / |
Label
Packaging Quantity: 0805/1206: 5000pcs/Reel, 2512: 4000pcs/Reel
Label shall mark the following items: (1) Size (2) Quantity (3) LOT.NO. (4) Manufacturers name
Peeling Test
Solder: Sn96.5 / Ag3 / Cu0.5
Peak Temperature: 240~260, 10 sec
Pre-heating Zone: 150 to 200 , 9030 sec
Soldering Zone: 230 or higher , 3010 sec
Care Note for Storage
Store in a controlled environment (temperature 535, relative humidity 4575% RH). Avoid direct sunlight, moisture, dust, and harmful gases (Hydrogen chloride, sulfurous acid gas, Hydrogen sulfide). Storage life: 1 year.
Recommended Reflow Soldering Profile
Preheating Zone: 150 to 200 , 9030 sec
Peak Temperature: 240~260, 10 sec
Soldering Zone: 230 or higher , 3010 sec
Care Note for Operating and Handling
- Avoid exceeding the normal rated power.
- Be careful when picking up with tweezers to prevent damage to the protective layer or resistance body.
- Do not touch the product with the soldering tip during manual installation.
2509261615_RVR-HIXD25NR024F_C52015931.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
