<
>
Specifications
Tolerance:
±5%
Voltage Rating:
100V
Capacitance:
47nF
Operating Temperature:
-40℃~+85℃
Dielectric Material:
Polyester
Mfr. Part #:
CL11-2A473J-100V
Package:
Through Hole,P=5mm
Key Attributes
Model Number:
CL11-2A473J-100V
Product Description
Product Overview
The CL11-2A series polyester film capacitor, manufactured by DAFU, offers reliable performance for various electronic applications. With a focus on quality and adherence to international standards, these capacitors are designed for durability and consistent operation.
Product Attributes
- Brand: (DAFU)
- Origin: (Dongguan DAFU Electronics Co., Ltd.)
- Material: Aluminum foil, film, epoxy resin, CP wire
- Certifications: ROHS
Technical Specifications
| Model | Rated Voltage (V) | Capacitance (PF/nF/F) | Tolerance | L (mm) | W1 (mm) | H1 (mm) | T1 (mm) | P0.5 (mm) | d0.05 (mm) |
|---|---|---|---|---|---|---|---|---|---|
| CL11-2A473J-100V | 100 | 0.047F (473) | J (5%) | 25 | 8.0 | 11.0 | 4.0 | 5.0 | 0.5 |
| CL11-2A104J-100V | 100 | 0.1F (104) | J (5%) | 25 | 8.0 | 12.0 | 4.5 | 5.0 | 0.5 |
| CL11-2A103J-100V | 100 | 0.01F (103) | J (5%) | 25 | 6.5 | 9.0 | 3.0 | 5.0 | 0.5 |
| CL11-2A223J-100V | 100 | 0.022F (223) | J (5%) | 25 | 7.5 | 10.5 | 4.0 | 5.0 | 0.5 |
General Performance Requirements:
| Item | Performance Requirement | Test Method |
|---|---|---|
| Reference Standard | GB6346 (IEC60384-11) | |
| Operating Temperature | -40+85 | |
| Rated Voltage | 50V, 100V, 250V, 400V, 630V, 1000V | |
| Capacitance Tolerance | J (5%), K (10%) | Capacitance and dissipation factor measured at 252, using 10.1KHz, 1.0Vrms. |
| Dissipation Factor (D.F.) | tg1.0% | |
| Test Voltage | No breakdown or arcing | 2.0 times rated voltage applied between leads, charging current 50mA max, 60 seconds without damage. |
| Insulation Resistance (I.R.) | CR0.1F, I.R.30000M; CR0.1F, I.R.15000M | UR100V, Test voltage 10V, measure after 1min charge; UR100V, Test voltage 100V, measure after 1min charge. |
| Solderability | At least 95% of the area around the leads is uniformly covered with solder, and the body has no visible damage. | Solder temperature: 2355; Immersion time: 2.00.5S; Leads immersed in molten solder at 2355, 2.00.5mm from the body, shielded by an insulating plate 1.50.5mm thick. |
| Rapid Temperature Change | Appearance: No visible damage | Capacitors should withstand five temperature cycles. Sequence: Lower working temp (30min) -> Room temp (3min) -> Upper working temp (30min) -> Room temp (3min). |
| Lead Strength | Appearance: No visible damage | Vertical force (5N) applied to each lead for 101 seconds. For lead diameter 0.5mm. |
| Bending Strength | Appearance: No visible damage | Capacitor leads subjected to a 2.5N weight, bent 90 outwards, then returned; bent 90 in the opposite direction, then returned; bending cycle 2-3 seconds. For lead diameter 0.5mm. |
| Resistance to Soldering Heat | Appearance: No visible damage; Capacitance change rate: C/C2% (1KHz) | Solder temperature: 2605; Immersion time: 101S; Leads immersed in molten solder at 2605, 2.00.5mm from the body. |
| Damp Heat (Steady State) | Appearance: No visible damage; Capacitance change rate: C/C5% (1KHz); Dissipation factor (1KHz): 0.01 or 1.2 times initial measurement (whichever is greater); Insulation resistance: >50% of initial value | Capacitors placed in a test chamber: No voltage applied; Temperature: 402; Humidity: 93(+2,-3)%RH; Duration: 21 days. Measurement after 1-2 hours at room temperature post-test. |
| Vibration | Appearance: No visible damage | Capacitor leads soldered and vibration frequency range 10-500Hz, amplitude 0.75mm. Vibration from 10Hz to 500Hz and back to 10Hz in approximately one minute. Total time six hours, three times in mutually perpendicular directions every two hours. |
| Endurance | Appearance: No visible damage; Capacitance change rate: C/C5% (1KHz); Dissipation factor (1KHz): 0.01 or 1.2 times initial measurement (whichever is greater); Insulation resistance: >50% of initial value | Capacitors at 853, with 1.5 times rated voltage applied for 1000 hours. Voltage applied through a resistor equal to 1 per volt. Measurement after 1-2 hours at room temperature post-test. |
Storage Conditions:
- Storage Temperature and Humidity: -1040, 2575RH
- Storage Time: One year
Environmental Management Control Substances:
| No. | Hazardous Substance Type | Hazardous Substance Name | Limited Content |
|---|---|---|---|
| 1 | Heavy Metals | Cadmium and its compounds | 100ppm |
| Lead and its compounds | 1000ppm | ||
| Mercury and its compounds | 1000ppm | ||
| Hexavalent chromium compounds | 1000ppm | ||
| 2 | Organic Bromides | Polybrominated biphenyls (PBB) | 1000ppm |
| Polybrominated diphenyl ethers (PBDE) including DecaBDE | 1000ppm |
Test Report: (SGS report attached)
2204121730_NDF-CL11-2A473J-100V_C914542.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
