<
>
Specifications
Operating Temperature:
-25℃~+105℃
Lifetime:
-
Capacitance:
100uF
Height - Seated (Max):
30mm
Pin Spacing:
-
Voltage Rating:
450V
Diameter:
18mm
Equivalent Series Resistance(ESR):
-
Tolerance:
±20%
Ripple Current:
-
Mfr. Part #:
EKXJ451ELL101MM30S
Package:
Through Hole,D18xL30mm
Key Attributes
Model Number:
EKXJ451ELL101MM30S
Product Description
Product Overview
This specification defines the requirements for aluminum electrolytic capacitors, specifically the KXJ series. These capacitors are designed for various electronic applications requiring reliable performance and durability.
Product Attributes
- Brand: Nippon Chemi-Con Corporation
- Origin: Japan
- Sleeve Material: PET
- Terminal Plating Material: Sn
- Certifications: RoHS Directive (2011/65/EU)
Technical Specifications
| Item | Specification | Details |
|---|---|---|
| Category Temperature Range | -40 to +105 | |
| Rated Voltage Range | 450VDC | |
| Capacitance Tolerance | -20 to +20% | |
| Surge Voltage | 495VDC (at 450VDC rated voltage) | See Table-1 |
| Dissipation Factor (tan ) | See Standard Rating Table | |
| Leakage Current | See Standard Rating Table | Measured after specified period at rated voltage with 1000 resistor. Shall not exceed specified values. |
| Rated Ripple Current | See Standard Rating Table | Multipliers provided for different frequencies. |
| Marking | Rated voltage, Rated capacitance, Upper category temperature, Negative polarity marking, Manufacturers identification mark, Capacitance tolerance code, Lot No., Series name. | White marking. Negative polarity marking (stripe) on lead. |
| Performance Conditions | Temperature: +15 to +35, Humidity: 45 to 75% RH, Atmospheric pressure: 86 to 106kPa. For judgment: +202, 60 to 70% RH, 86 to 106kPa. | |
| Capacitance Measurement | Frequency: 120Hz 20%, Voltage: 0.5Vrms max. +1.5 to 2.0VDC. Circuit: Series equivalent. | Shall be within specified capacitance tolerance. |
| Dissipation Factor Measurement | Frequency: 120Hz 20%, Voltage: 0.5Vrms max. +1.5 to 2.0VDC. Circuit: Series equivalent. | Shall not exceed values specified in Standard Ratings Table. |
| Terminal Strength - Pull | Lead diameter > 0.5 to 0.8mm: 10N pull force for 101 sec. | Lead wire shall neither loosen nor break away. |
| Terminal Strength - Bending | Lead diameter > 0.5 to 0.8mm: 5N bending load. | Lead wire shall neither loosen nor break away. |
| Soldering Heat | Solder: Sn-3Ag-0.5Cu, Flux: Ethanol solution (25 wt.% rosin). Temp/Time: +2605 for 101 sec OR +38010 for 30.5 sec. Depth: 1.5 to 2.0mm. Speed: 252.5mm/sec. | No significant damage, legible marking, no electrolyte leakage. Capacitance change within 10%. Tan within initial specified value. |
| Solderability | Solder: Sn-3Ag-0.5Cu, Flux: Ethanol solution (25 wt.% rosin). Temp: +2453. Depth: 1.5 to 2.0mm. Time: 2 to 3 sec. | Solder shall cover at least 3/4 of the immersed lead surface. |
| Vibration | Frequency: 10 to 55Hz. Amplitude/Acceleration: 0.75 mm or 98m/s (whichever is less severe). Sweep: 10 to 55 to 10Hz in 1 min. Duration: 2 hours each in 3 directions (total 6 hours). | No significant damage, legible marking, no electrolyte leakage. Capacitance change within 5%. |
| Damp Heat | Temp: +402, Humidity: 90 to 95% RH. Time: 2408 hours. | No significant damage, legible marking, no electrolyte leakage. Leakage current within initial value. Capacitance change within 20%. Tan not exceed 120% of initial value. |
| Endurance | DC voltage with rated ripple current at +1052 for 12,000+72/-0 hours. Sum of DC and peak AC voltage must not exceed rated voltage. | No significant damage, legible marking, no electrolyte leakage. Leakage current within initial value. Capacitance change within 20%. Tan not exceed 200% of initial value. |
| Surge Voltage Test | Temp: +15 to +35. Resistor: 100010 . Voltage: Surge voltage (Table-1). Apply 305 sec every 60.5 min. Cycle: 1000 cycles. | No significant damage, no electrolyte leakage. Leakage current within initial value. Capacitance change within 20%. Tan not exceed 200% of initial value. |
| Pressure Relief Vent | Reverse voltage with 1 amp DC current. | Capacitor shall not flame. If vent does not operate within 30 minutes, test is passed. |
| High Temperature Storage | 1,000+48/-0 hours at +1052 without voltage. Preconditioned per JIS C 5101-4 Item 4.1. | No significant damage, legible marking, no electrolyte leakage. Leakage current within initial specified value. |
2410121725_NCC-EKXJ451ELL101MM30S_C961212.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
