<
>
Specifications
Lifetime:
1000hrs@105℃
Capacitance:
100uF
Height - Seated (Max):
11.5mm
Pin Spacing:
3.5mm
Voltage Rating:
50V
Diameter:
8mm
Tolerance:
±20%
Mfr. Part #:
ECR1HLH101MLL080011
Package:
Through Hole,D8xL11.5mm
Key Attributes
Model Number:
ECR1HLH101MLL080011
Product Description
Product Specification - CD281L Series Aluminum Electrolytic Capacitor
This product specification is adapted to CD281L series Aluminum Electrolytic Capacitors produced by Nantong Jianghai Capacitor Co.,Ltd. These capacitors are designed for a wide operating temperature range of -55 to +105.
Product Attributes
- Brand: (Nantong Jianghai Capacitor Co.,Ltd)
- Origin: P.R. China
- Product Series: CD281L Series
- Product Name: Aluminum Electrolytic Capacitor
- Date of Issue: December 31, 2019
Technical Specifications
| Customer P/N | Jianghai P/N | Voltage WV (V) | Capacitance CAP (uF) | Leakage Current LC (uA) 20 2min | Dissipation Factor tan (%) 120Hz | Impedance () 100KHz 20 | Ripple Current (mArms) at 105 100KHz | Load Life (hrs) | Dimensions DxL mmxmm |
| ECR1HLH101MLL080011 | 50 | 100 | 100 | 0.2 | 360 | 7000 | 8*11.5 |
General Specifications
| Item | Conditions | Specifications |
| Operating Temperature Range | -55+105 | |
| Surge Voltage | Rated voltage (V) | 6.3, 10, 16, 25, 35, 50, 63, 100 |
| Surge voltage (V) | 7.2, 13, 20, 32, 44, 63, 79, 125 | |
| Dissipation Factor (20, 120HZ) | Rated voltage (V) | 6.3, 10, 16, 25, 35, 50, 63, 100 |
| Tan (%) MAX | 22, 19, 16, 14, 12, 10, 9, 8 | |
| Capacitance Range | 0.47uF - 15000uF | |
| Marking | Item | Contents |
| 1. Brand | ||
| 2. Products series | CD281L | |
| 3. Upper temperature limit | 105 | |
| 4. Year code | ||
| 5. Rated voltage | ||
| 6. Capacitance | ||
| 7. Polarity |
Performance Characteristics
| No. | Items | Conditions | Specifications |
| 9.1 | Maximum permissible ripple current | Temperature: 1052; Voltage: DC Voltage + peak ripple voltage Rated voltage | Refer to spec. list |
| 9.2 | Surge Voltage Test | 1000 cycles at specified temperature (30s charge, 5min 30s discharge), 1-2 hours thermal stability. Test voltage: see item 3; Test Temperature: 1530 | Leakage Current: Not more than specified value; Capacitance change: Within 15% of initial value; Dissipation Factor: Not more than specified value |
| 9.3 | Capacitance (Tolerance) | Measuring frequency: 120 HZ; Measuring voltage: 0.5Vrms; DC bias voltage: +1.52.0 V DC | Capacitance Tolerance: 20% |
| 9.4 | Dissipation Factor (tg) | Same conditions as Capacitance measurement | Refer to table 4 |
| 9.5 | Leakage Current | 6.3--100WV: Less than 0.02CV or 3uA whichever larger (2min) | Leakage current: (I)=E/Rs |
| 9.6 | Characteristic at High and low temperature | Step 1: Measure Capacitance, Dissipation Factor and impedance. Step 2: Store at -55(-40)3 for 2 hours, then measure. Step 4: Store at 1052 for 2 hours, then measure. | Step 2: Impedance ratio (vs Step 1) per 9.10; Capacitance change (vs Step 1): -200%; Step 4: Capacitance change (vs Step 1): 0+20%; Leakage Current: Less than 500% of specified value |
| 9.7 | Pressure relief | AC test: AC voltage 0.7 x rated DC voltage or 250V AC (whichever is lower), Frequency: 50/60Hz. DC test: Reversed polarity DC rated voltage, current limited to 1A. | No fire, explosion, or separation of case/seal. Applicable to capacitors with diameter 6mm. |
| 9.8 | Load life | 1052, applied max ripple current, DC+AC peak voltage rated voltage. Duration per table. Measured after 16 hours at standard conditions. | Leakage current: Initial specified value; Capacitance change: Within 25% of initial value; Dissipation factor: 200% of initial specified value |
| 9.9 | Shelf life | Temp: 1052, Time: 1000+36 hours. DC rated voltage applied for 30 mins through 1K resistor, then stored 24-48 hours at standard conditions. | Leakage current: Initial specified value; Capacitance change: Within 20% of initial value; Dissipation factor: 200% of initial specified value |
| 9.10 | Impedance stability | Rated voltage (V): 6.3, 10, 16, 25, 35, 50, 63, 100 | Impedance (120Hz) Z -55/+20: 3 |
| 9.11 | Solder ability | Solder press time: 20.5s; Solder temperature: 2455 | At least 90% of circumferential surface of the dipped portion of termination shall be covered with new solder |
| 9.12 | Resistance to soldering heat | Test Temperature: 260 5; Test time: 101s | Leakage Current: Not more than specified value; Capacitance Change: Within 10% of initial value; Dissipation Factor: Not More than specified value; Appearance: No defects |
| 9.13 | Resistance of damp heat | Test Temperature: 40 2; Humidity: 90-95% |
2410121534_Nantong-Jianghai-Capacitor-ECR1HLH101MLL080011_C233122.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
