<
>
Specifications
Voltage Rating:
16V
Capacitance:
560uF
Lifetime:
-
Tolerance:
±20%
Pin Spacing:
-
Equivalent Series Resistance(ESR):
-
Height - Seated (Max):
11.5mm
Operating Temperature:
-55℃~+105℃
Diameter:
8mm
Ripple Current:
-
Mfr. Part #:
PCR1CEN561MBABCC35WP
Package:
Through Hole,D8xL11.5mm
Key Attributes
Model Number:
PCR1CEN561MBABCC35WP
Product Description
Product Overview
This specification is applicable to HEN series aluminum electrolytic capacitors with conductive polymer solid electrolyte. These capacitors are designed for applications requiring reliable performance and long lifespan.
Product Attributes
- Brand: Jianghai
- Origin: Nantong Jianghai Capacitor Co., Ltd., PR China
- Product Type: Aluminium electrolytic capacitors with conductive polymer solid electrolyte
- Product Series: HEN Series
- Default Marking Color: Red (adjustable per customer demand)
Technical Specifications
| Item | Specifications | Test Method |
| Rated voltage | 16 V | |
| Rated capacitance | 220~560 F (20, 120Hz) | |
| Tolerance on rated capacitance | 20 % | |
| Surge voltage | UR 1.15 | |
| Leakage current | See specifications list (20, After 2 minutes) | Series resistor: 1,000 Applied rated voltage 2 minutes. If this value is doubtful, performed the voltage treatment. Voltage treatment: The capacitor should be serially attached to a protective 1,000 resistor and d.c. voltage equivalent to the rated voltage should be applied for 2h at 105 2. Next, after letting the capacitor cool to room temperature, it should be discharged through a resistor of approximately 1 /V and then stored at standard atmospheric conditions for 12 h to 24 h. |
| Tangent of loss angle (tan) | See specifications list (20, 120Hz) | Measuring temperature: 202 |
| Equivalent series resistance (ESR) | See specifications list (100 kHz) | Frequency: 100 kHz10% Measuring voltage: 0.5Vrms, Measuring temperature: 202 |
| Rated ripple current | See specifications list (105, 100 kHz) | |
| Category temperature range | -55 to 105 | |
| Lifespan | 105 , 2000 h | |
| Frequency coefficient for ripple current | 120Hz1kHz: 0.05; 1kHz10kHz: 0.3; 10kHz100kHz: 0.7; 100kHz500kHz: 1.0 | |
| Solderability | At least 95% of circumferential surface of the dipped portion of termination shall be covered with new solder. | Solder bath method Flux: Rosin // Ethanol, About 25 wt% Sn-Ag-Cu solder Temperature: 2453 Duration: 20.3 seconds |
| Robustness of terminations (Tensile) | See table | With the body of a capacitor fixed, the load shall be applied to the lead wire termination in its draw out direction, gradually up to the specified value. |
| Robustness of terminations (Bending) | See table | Suspend a weight corresponding to bending strength, bend the body through 90and return it to the original position. Carry out these operations during 2 to 3 seconds and count it as one cycle. Carry out similar operations in the opposite direction and count it as two cycles. |
| Resistance to soldering heat | Capacitance change: Within 5% of initial value. Tan: Within the value of item 2. Leakage current: Within the value of item 2. | A) Solder bath method Temperature: 2605C, Duration: 10 1 seconds B) Soldering iron method Temperature: 40010C Duration: 3+1/0 seconds Heat protector: t=1.6 mm glass-epoxy board. |
| Vibration | Capacitance: Shall not show drastic change compared to initial capacitance when measured within 30 minutes. Capacitance change: Within 5% of the initial value. Appearance: No visible damage, Legible marking. | Frequency: 10 to 55 Hz (1 minute interval / 10 55 10 Hz) Amplitude: 0.75 mm (Total excursion 1.5 mm) Direction: X, Y, Z (3 axes) Duration: 2 hours / axial (Total 6 hours) The capacitors are supported as the following figure: |
| Rapid change of temperature | Capacitance change: Within 10% of initial value. Tan: Within the value of item 2. Leakage current: Within the value of item 2. Appearance: No visible damage, Legible marking. | TA= -55 TB= 105 Cycle number: 5 cycles Applied voltage: Without load |
| Shelf Life | Capacitance change: Within 20% of initial value. Tan: Within 2 times of the value of item 2. Leakage current: Within the value of item 2. | Temperature: 105 2 Time: 1000+36 hours Condition: The DC rated voltage shall be applied across the capacitor and its protective resistor (1K) for 30 minutes. The capacitor shall then be stored under standard atmospheric conditions for 24 ~ 48 hours. |
| Endurance | Capacitance change: Within 20% of initial value. Tan: Within 1.5 times of the value of item 2. ESR: Within 1.5 times of the value of item 2. Leakage current: Within the value of item 2. Appearance: No visible damage, Legible marking. | Temperature: 105 2 Duration: 2000 +48/-0h Applied voltage: Rated voltage |
| Damp heat, steady state | Capacitance change: Within 20% of initial value. Tan: Within 1.5 times of the value of item 2. ESR: Within 1.5 times of the value of item 2. | Temperature: 602 Relative humidity: 90 ~ 95% Duration: 1,000 +24/-0 hours |
| Rated voltage (V) | Rated capacitance (F) | Case size (D*L) | Jianghai Part No. | Customer Part No. | DF (%) 20 120Hz | LC (A) 20 2min | ESR value (m) RC | Ripple value (mArms) 105, 100 kHz | Lifespan (h) |
| 16 | 270 | 6.3*8 | PCR1CEN271MF08CC32WP | JH-HEN1C271M-1 | 8 | 864 | 15 | 3600 | 2000 |
| 16 | 560 | 8*11.5 | PCR1CEN561MBABCC35WP | JH-HEN1C561M-1 | 12 | 1792 | 11 | 5100 | 2000 |
| 16 | 220 | 6.3*8 | PCR1CEN221MF08CC33WP | JH-HEN1C221M-1 | 8 | 704 | 15 | 3000 | 2000 |
| 16 | 270 | 6.3*8 | PCR1CEN271MF08CC33WP | JH-HEN1C271M-2 | 8 | 864 | 15 | 3600 | 2000 |
| Code | D0.5 | L | max | F0.5 | d0.05 | H0.5 |
| F08 | 6.3 | 8 | 1 | 2.5 | 0.5 | 3.2 |
| BAB | 8 | 11.5 | 1.5 | 3.5 | 0.6 | 3.5 |
| F08 | 6.3 | 8 | 1 | 2.5 | 0.5 | 3.3 |
| F08 | 6.3 | 8 | 1 | 2.5 | 0.5 | 3.3 |
2201121230_Nantong-Jianghai-Capacitor-PCR1CEN561MBABCC35WP_C2918277.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
