<
>
Specifications
Voltage Rating:
63V
Capacitance:
68uF
Lifetime:
-
Tolerance:
±20%
Pin Spacing:
-
Height - Seated (Max):
10mm
Equivalent Series Resistance(ESR):
-
Ripple Current:
-
Diameter:
10mm
Operating Temperature:
-55℃~+105℃
Mfr. Part #:
PHV1JVB680MC10FVTSWP
Package:
SMD,D10xL10mm
Key Attributes
Model Number:
PHV1JVB680MC10FVTSWP
Product Description
Product Overview
This specification applies to the PHVB series conductive polymer hybrid aluminum electrolytic capacitors. Designed for demanding applications, these capacitors offer a robust solution with advanced materials and construction.
Product Attributes
- Brand: Jianghai
- Origin: Nantong Jianghai Capacitor Co., Ltd., China
- Product Type: Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
- Product Series: PHVB Series
Technical Specifications
| Item | Specifications | Test Method |
|---|---|---|
| Rated voltage | 63 V | |
| Rated capacitance | 68 F | 20,120Hz |
| Case size | 10 10 | |
| Tolerance on rated capacitance | 20 % | |
| Surge voltage | 72.5 V | |
| Leakage current | 42.84 A (max.) | 20, After 2 minutes |
| Tangent of loss angle (tan) | 8 % (max.) | 20,120Hz |
| Equivalent series resistance (ESR) | 30 m (max.) | 100 kHz |
| Rated ripple current | 1400 mA | 125 100kHz |
| Category temperature range | -55 to 125 | |
| Lifespan* | 125 , 4000 h | *The failure rate of capacitors follows JIS C 5003 standard, with a reliability level of 60 %, as follows: 0.5 % / 1,000 hours (Maximum operating temperature, load rated voltage ) |
| Leakage current | See specifications list | Series resistor: 1,000 Applied rated voltage 2 minutes. If this value is doubtful, performed the voltage treatment. Voltage treatment: The capacitor should be serially attached to a protective 1,000 resistor and d.c. voltage equivalent to the rated voltage should be applied for 2h at 125 2.Next, after letting the capacitor cool to room temperature, it should be discharged through a resistor of approximately 1 /V and then stored at standard atmospheric conditions for 12 h to 24 h. |
| Capacitance | See specifications list | Measuring circuit: Equivalent series circuit Frequency: 120 Hz10% Measuring voltage: 0.5 Vrms |
| Tangent of loss angle (tan) | See specifications list | Measuring temperature: 202 |
| Equivalent Series Resistance (ESR) | See specifications list | Frequency: 100 kHz10% Measuring voltage: 0.5Vrms Measuring temperature: 202 |
| Solderability | At least 95% of circumferential surface of the dipped portion of termination shall be covered with new solder. | Solder temperature: 2455 Immerse and withdraw speed: 256mm/s Dwell time: 50.5s |
| Resistance to soldering heat change | Capacitance: Within 5% of the initial value; Tan: Within the value of item 2; Leakage current: Within the value of item 2; Appearance: No visible damage, Legible marking | Temperature: 2605C Duration: 10 1 seconds |
| Rapid change of temperature change | Capacitance: Within 10% of the initial value; Tan: Within the value of item 2; Leakage current: Within the value of item 2; Appearance: No visible damage, Legible marking | Applied voltage: Without load Cycle number: 5 cycles TA=-55 TB= 125 |
| Vibration | Capacitance Change: Within 10% of the initial value; Tan: Within the value of item 2; Leakage current: Within the value of item 2; Appearance: No visible damage, Legible marking | Frequency: 10~55 Hz (reciprocation for 1 min) Total amplitudes: 0.75mm Direction: X, Y, Z (3 axes) Duration:3 orthogonal directions, each for 2hrs . |
| Endurance | Capacitance change: Within 30% of the initial value; Tan: Within 2 times of the value of item 2; Leakage current: Within the value of item 2; Appearance: No visible damage, Legible marking | Temperature: 125 2 Duration: 4000 +48/-0h Applied voltage: Rated voltage Ripple current:Rated ripple current |
| Damp heat, steady state change | Capacitance: Within 20% of the initial value; Tan: Within 2 times of the value of item 2; Leakage current: Within the value of item 2 (After voltage treatment); Appearance: No visible damage, Legible marking | Temperature: 402 Relative humidity: 90 ~ 95% Duration: 240 +8/-8 hours |
| Surge | Capacitance change: Within 20% of the initial value; Tan: Within 1.5 times of the value of item 2; Leakage current: Within the value of item 2; Appearance: No visible damage, Legible marking | Temperature: Normal temperature Applied voltage: 72.5 V Protective resistor: 1 k Cycle number: 1,000 cycles (A) Charge: 305 seconds (B) Discharge: 5.5 minutes (A) + (B): 1 cycle |
| High and low temperature characteristics | Capacitance change: Within 20% of Step 1's Capacitance; Impedance ratio at 120Hz Z(-55)/Z(+20) 2 | Step 1: +202 Step 2: -553 Step 3: +202 Step 4: +1252 Step 5: +202 |
| Resistance To Solvents | Print cannot fall off or ambiguous | Method 1: 1.The capacitor shall be immersed into the isopropyl 2. Immersion time: 3 +0.5/-0 minutes at 255 3.Use wool brush to brush capacitor for 10 times Repeat step 1~3 for 3 times Method 2: 1.The capacitor shall be immersed into the demineralized or distilled Water 2. Immersion time: 3 +0.5/-0 minutes at 50-60 3.Use wool brush to brush capacitor for 10 times Repeat step 1~3 for 3 times |
| Reflow soldering judgment | Capacitance change: Within 10% of the initial value | Reflow soldering conditions should follow our standard or mutual communication. |
2409292132_Nantong-Jianghai-Capacitor-PHV1JVB680MC10FVTSWP_C2918313.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
