Wire Wound Chip Common Mode Choke Coil DLW32SH_XF Series
This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW32SH_XF Series for Automotive Electronics based on AEC-Q200. These coils are designed for common mode noise suppression in automotive electronic applications.
Product Attributes
- Brand: MURATA MFG.CO.,LTD
- Series: DLW32SH_XF Series
- Certification: AEC-Q200
- Mounting Type: Chip
- Polarity: No polarity
- Marking: No Marking
Technical Specifications
| Murata Part Number | Common Mode Inductance (uH) (at 0.1MHz) | Rated Voltage V(DC) | Rated Current (mA) | DC Resistance ( max.) | ESD Rank | Operating Temperature | Storage Temperature |
|---|---|---|---|---|---|---|---|
| DLW32SH101XF2L | 100 (-30%/+50%) | 50 | 115 | 2.1 | 5B (12kV(AD) < 16kV(AD)) | -40 to +125C | -40 to +125C |
AEC-Q200 Requirements
| Stress Test Method | Specification | Test Condition |
|---|---|---|
| High Temperature Exposure | Common Mode Inductance Change: Within 20% | 1000hours at 125 deg C, Set for 24hours at room temperature, then measured. |
| Temperature Cycling | Meet Table A after testing. | 1000cycles -40 deg C to +125 deg C, Set for 24hours at room temperature, then measured. |
| Biased Humidity | Meet Table A after testing. | 1000hours at 85 deg C, 85%RH, Apply max rated current. Set for 24hours at room temperature, then measured. |
| Operational Life | Meet Table A after testing. | 1000hours at 125 deg C, Apply max rated current, Set for 24hours at room temperature, then measured. |
| Mechanical Shock | Meet Table A after testing. | Per MIL-STD-202 Method 213 Condition F: 1500g's(14.7N)/0.5ms/Half sine |
| Vibration | Meet Table A after testing. | 5g's(0.049N) for 20 minutes, 12cycles each of 3 orientations, Test from 10-2000Hz. |
| Resistance to Soldering Heat | Meet Table A after testing. | Solder temperature 260C+/-5 deg C, Immersion time 10s, Pre-heating:150 to 180 deg C / 9030s |
| ESD | Meet Item 3 (Rating) | Per AEC-Q200-002 |
| Board Flex | Meet Table A after testing. | Epoxy-PCB(1.6mm), Deflection 2mm(min), Holding time 60s |
| Terminal Strength | No defects | Per AEC-Q200-006, A force of 17.7N for 60s |
Packaging Specifications
| Packaging Code | Reel Diameter | Standard Quantity | Pull Strength of Plastic Tape | Pull Strength of Cover Tape | Peeling off force of Cover Tape |
|---|---|---|---|---|---|
| L | 180mm | 1500 pcs. / reel | 5 N min. | 10 N min. | 0.2N to 0.7N |
Caution
Mount products in the right direction. Wrong direction may cause open or short circuit, flames, or other serious trouble. Do not exceed maximum rated current. Provide appropriate fail-safe functions to prevent secondary damage. Products can only be soldered with reflow. Do not clean after soldering unless approved. Resin coating may affect inductance value and cause open circuits. Avoid highly acidic or water-soluble flux and use Sn-3.0Ag-0.5Cu solder with a standard thickness of 150m.
2410121526_muRata-DLW32SH101XF2L_C1857795.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
