<
>
Specifications
Operating Temperature:
-45℃~+105℃
Lifetime:
2000hrs@105℃
Capacitance:
22uF
Height - Seated (Max):
17mm
Pin Spacing:
5mm
Voltage Rating:
400V
Diameter:
12.5mm
Tolerance:
±20%
Mfr. Part #:
EKM226M2GI17CA
Package:
Through Hole,D12.5xL17mm
Key Attributes
Model Number:
EKM226M2GI17CA
Product Description
Product Overview
The SAMXON KM Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with an aluminum case, end seal rubber, and PET sleeve. They are suitable for applications requiring reliable performance with specific electrical characteristics, including rated voltage, capacitance, leakage current, and temperature range.
Product Attributes
- Brand: SAMXON
- Series: KM Series
- Construction Type: Single ended, foil type
- Sleeve Material: PET
- Lead Line Material: Tinned CP wire (Pb Free)
- Terminal Material: Aluminum wire
- Sealing Material: Rubber
- Case Material: Aluminum case
- Separator Material: Electrolyte paper
- Standard Compliance: IEC60384
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap tolerance | Temp. range() | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 120Hz (mA rms) | ESR at 20 100kHz () | Load lifetime (Hrs) | Dimension (mm) DL | Shape Code F (Pitch) | Shape Code H (Height) | Shape Code d (Lead Dia.) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EKM226M2GI17CA**R1 | 400 | 22 | -20%~+20% | -25~105 | 0.24 | 304 | 150 | 3 | 2000 | 12.5X17 | 5.0 | 3.0 | 0.6 |
General Characteristics
| Item | Description |
|---|---|
| Rated voltage (WV) | 6.3, 10, 16, 25, 35, 50, 63, 100, 160, 200, 220, 250, 350, 400, 420, 450 V.DC |
| Surge voltage (SV) | 8, 13, 20, 32, 44, 63, 79, 125, 200, 250, 270, 300, 400, 450, 470, 500 V.DC |
| Nominal capacitance (Tolerance) | Measured at 120Hz12Hz, 0.5Vrms, 202. Shall be within specified tolerance. |
| Leakage current | Measured after 2 minutes with a 1k 10 series resistor. Refer to Table 1. |
| tan | Measured at 120Hz, 202. Refer to Table 1. |
| Terminal strength (Tensile) | 0.5mm and less: 5 N (0.51 kgf); Over 0.5mm to 0.8mm: 10 N (1.0 kgf) |
| Terminal strength (Bending) | 0.5mm and less: 2.5 N (0.25 kgf); Over 0.5mm to 0.8mm: 5 N (0.51 kgf) |
| Load life test | 105C 2, DC bias voltage + rated ripple current for 2000 Hrs. Criteria: Leakage current within specified value, Capacitance change within 20%, tan not more than 200% of specified value, no electrolyte leakage. |
| Shelf life test | 1052 for 1000+48/0 hours. Criteria: Leakage current within specified value, Capacitance change within 20%, tan not more than 200% of specified value, no electrolyte leakage. |
| Surge test | 1000 cycles of charge (305s) and discharge (5 min 30s) with surge voltage. Criteria: Leakage current within specified value, Capacitance change within 15%, tan within specified value, no electrolyte leakage. |
| Vibration test | 10Hz ~ 55Hz, 1.5mm peak to peak amplitude for 2 hours in 3 directions. Criteria: No intermittent contacts, open/short circuit, damage, leakage, or swelling. Markings legible. |
| Solderability test | Soldering temperature: 2453, Dipping depth: 2mm, Dipping speed: 252.5mm/s, Dipping time: 30.5s. Criteria: Minimum 95% of immersed surface coated. |
| Resistance to solder heat test | Solder bath at 2605 for 101 seconds or 40010 for 3+0/-1 seconds to 1.5~2.0mm from body. Criteria: Leakage current within specified value, Capacitance change within 10%, tan within specified value, no electrolyte leakage. |
| Change of temperature test | 5 cycles of temperature change (-40 to +105). Criteria: Leakage current within specified value, tan within specified value, no electrolyte leakage. |
| Damp heat test | 90~95% RH at 402 for 5008 hours. Criteria: Leakage current within specified value, Capacitance change within 20%, tan not more than 120% of specified value, no electrolyte leakage. |
| Vent test | Applies to products with vent (diameter 6.3mm). DC test with reversed polarity. Criteria: Vent operates with no dangerous conditions (flames, dispersion of pieces). |
| Maximum permissible ripple current | Maximum AC current at 120Hz and maximum operating temperature. Combined DC and peak AC voltage shall not exceed rated voltage. Frequency multipliers provided for different frequencies and voltage/capacitance ratings. |
2411261600_Man-Yue-Tech-EKM226M2GI17CA_C2903590.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
