Product Overview

This specification applies to polar Aluminum electrolytic capacitors (foil type) designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with an aluminum case, sealed with end seal rubber, and finished with a vinyl sleeve. They are suitable for general electronic applications requiring reliable performance.

Product Attributes

• Brand: SAMXON
• Series: RD Series
• Construction Type: Single ended, foil type
• Sleeve Material: PET
• Sealing Material: Rubber
• Lead Wire Material: Tinned CP wire (Pb Free)
• Terminal Material: Aluminum wire
• Separator Material: Electrolyte paper
• Case Material: Aluminum case

Technical Specifications

General Characteristics

• Standard Atmospheric Conditions: Ambient temperature: 15C to 35C, Relative humidity: 45% to 85%, Air Pressure: 86kPa to 106kPa.
• Measurement Conditions: Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa.
• Operating Temperature Range: Refer to Table 1.
• Rated Voltage (WV): 160 V.DC
• Surge Voltage (SV): 200 V.DC
• Nominal Capacitance Measurement: 120Hz12Hz, not more than 0.5Vrms, 202.
• Leakage Current Measurement: Connected with a protective resistor (1k10) in series for 2 minutes.
• tan Measurement: At 120Hz12Hz, not more than 0.5Vrms, 202.
• Terminal Strength: Tensile force (0.5mm and less): 5 N (0.51 kgf); Bending force (0.5mm and less): 2.5 N (0.25 kgf).
• Load Life Test: 105C 2, DC bias voltage plus rated ripple current for Table 1, 16 hours recovering time. Criteria: Leakage current within specified value, Capacitance Change within 20%, tan not more than 200% of specified value, no electrolyte leakage.
• Shelf Life Test: Stored at 1052 for 1000+48/0 hours. Criteria: Leakage current within specified value, Capacitance Change within 20%, tan not more than 200% of specified value, no electrolyte leakage.
• Surge Test: 1000 cycles of charge (305s) and discharge (5 min 30s) with surge voltage. Criteria: Leakage current not more than specified value, Capacitance Change within 15%, tan not more than specified value, no electrolyte leakage.
• Vibration Test: 10Hz ~ 55Hz, 1.5mm peak to peak amplitude for 2 hours in each of 3 directions.
• Solderability Test: Soldering temperature: 2453C, Dipping depth: 2mm, Dipping speed: 252.5mm/s, Dipping time: 30.5s. Criteria: Minimum 95% of immersed surface coated.
• Resistance to Solder Heat Test: 2605 for 101 seconds or 40010 for 3 + 0 1 seconds. Criteria: Leakage current not more than specified value, Capacitance Change within 10%, tan not more than specified value, no electrolyte leakage.
• Change of Temperature Test: 5 cycles of temperature changes (-25/-40 to +105). Criteria: Leakage current not more than specified value, tan not more than specified value, no electrolyte leakage.
• Damp Heat Test: 90~95% RH at 402 for 5008 hours. Criteria: Leakage current not more than specified value, Capacitance Change within 20%, tan not more than 120% of specified value, no electrolyte leakage.
• Vent Test: For products with vent (diameter 6.3). Operates with no dangerous conditions.
• Maximum Permissible Ripple Current: Maximum AC current at 120Hz and maximum operating temperature.