<
>
Specifications
Operating Temperature:
-45℃~+105℃
Lifetime:
12000hrs@105℃
Capacitance:
180uF
Height - Seated (Max):
40mm
Pin Spacing:
7.5mm
Voltage Rating:
420V
Diameter:
18mm
Tolerance:
±20%
Mfr. Part #:
ERH187M2ML40RR
Package:
Through Hole,D18xL40mm
Key Attributes
Model Number:
ERH187M2ML40RR
Product Description
Product Overview
The SAMXON RH Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with an aluminum case, sealed with end seal rubber, and finished with a vinyl sleeve. They are suitable for general electronic applications requiring reliable performance.
Product Attributes
- Brand: SAMXON
- Series: RH Series
- Construction Type: Single ended, foil type
- Sleeve Material: PVC/PET
- Lead Line Material: Tinned CP wire (Pb Free)
- Terminal Material: Aluminum wire
- Sealing Material: Rubber
- Separator Material: Electrolyte paper
- Case Material: Aluminum case
- Standard Compliance: IEC60384
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap. tolerance | Temp. range () | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100kHz (mA rms) | Load lifetime (Hrs) | Dimension (mm) DL | F | d | Sleeve |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ERH187M2ML40RR**F-R | 420 | 180 | -20%~+20% | -25~105 | 0.20 | 1537 | 2000 | 12000 | 18X40 | 7.5 | 0.8 | PET |
Additional Technical Data
| Item | Description |
|---|---|
| Rated voltage (WV) | WV (V.DC): 160, 200, 250, 350, 400, 450, 500 |
| Surge voltage (SV) | SV (V.DC): 200, 250, 300, 400, 450, 500, 550 |
| Nominal capacitance measurement conditions | Frequency: 120Hz12Hz, Voltage: 0.5Vrms, Temperature: 202 |
| Leakage current measurement conditions | Connected with a protective resistor (1k 10 ) in series for 2 minutes |
| tan measurement conditions | Refer to nominal capacitance measurement conditions |
| Terminal strength (Tensile force) | 0.5mm and less: 5 N (0.51 kgf); Over 0.5mm to 0.8mm: 10 N (1.0 kgf) |
| Terminal strength (Bending force) | 0.5mm and less: 2.5 N (0.25 kgf); Over 0.5mm to 0.8mm: 5 N (0.51 kgf) |
| Load life test conditions | 105C 2, DC bias voltage + rated ripple current, tested after 16 hours recovery |
| Shelf life test conditions | 1052 for 1000+48/0 hours, followed by 4~8 hours stabilization at room temperature, then DC rated voltage applied for 30min via 1k100 resistor |
| Surge test conditions | 1000 cycles of 305s charge and 5 min 30s discharge, with a resistor (100 50)/CR (k), at 15~35 |
| Vibration test conditions | 10Hz ~ 55Hz, 1.5mm peak to peak amplitude, for 2 hours in each of 3 mutually perpendicular directions |
| Solderability test conditions | Soldering temperature: 2453, Dipping depth: 2mm, Dipping speed: 252.5mm/s, Dipping time: 30.5s |
| Resistance to solder heat test conditions | Solder bath at 2605 for 101s or 40010 for 3 0 1 s, 1.5~2.0mm from body |
| Change of temperature test conditions | 5 cycles of: (1)+20 (3 min), (2)-25 (302 min), (3)+105 (302 min) |
| Damp heat test conditions | 90~95% RH at 402 for 5008 hours |
| Vent test conditions (for 6.3) | DC test with reversed polarity, applied current from Table 2 (e.g., 1A for diameter 22.4mm) |
| Maximum permissible ripple current | Maximum AC current at 100kHz and maximum operating temperature. Combined DC and AC peak voltage must not exceed rated voltage. |
2411272239_Man-Yue-Tech-ERH187M2ML40RR_C2903602.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
