Product Overview
The SAMXON GF Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. Meeting IEC60384 standards, these capacitors are constructed with an aluminum case, end seal rubber, and a PET sleeve. They are suitable for applications requiring reliable performance across a wide temperature range of -40C to 105C. The series offers various voltage and capacitance ratings, with a focus on stable electrical parameters and long-term reliability.
Product Attributes
- Brand: SAMXON
- Series: GF Series
- Construction Type: Single ended, foil type
- Sleeve Material: PET
- Lead Material: Tinned CP wire (Pb Free)
- Case Material: Aluminum case
- Sealing Material: Rubber
- Separator Material: Electrolyte paper
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap. tolerance | Temp. range() | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100kHz (mA rms) | Impedance at 20 100kHz (max) | Load lifetime (Hrs) | Dimension (mm) DL | F (mm) | d (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1EGF227M1EF12CB**P | 25 | 220 | -20%~+20% | -40~105 | 0.14 | 55 | 640 | 0.130 | 3000 | 8x12 | 3.5 | 0.5 |
General Characteristics
| ITEM | PERFORMANCE |
|---|---|
| Rated voltage (WV) | WV (V.DC): 6.3, 10, 16, 25, 35, 50, 63, 100 SV (V.DC): 8, 13, 20, 32, 44, 63, 79, 125 |
| Nominal capacitance (Tolerance) | Measuring Frequency: 120Hz12Hz Measuring Voltage: Not more than 0.5Vrms Measuring Temperature: 202 Criteria: Shall be within the specified capacitance tolerance. |
| Leakage current | Condition: Connect with a protective resistor (1k 10 ) in series for 2 minutes, then measure. Criteria: Refer to Table 1. |
| tan | Condition: See 4.2 for measuring frequency, voltage and temperature. Criteria: Refer to Table 1. |
| Terminal strength | Tensile Strength: 0.5mm and less: 5 N (0.51 kgf); Over 0.5mm to 0.8mm: 10 N (1.0 kgf) Bending Strength: 0.5mm and less: 2.5 N (0.25 kgf); Over 0.5mm to 0.8mm: 5 N (0.51 kgf) Criteria: No noticeable changes, breakage or looseness at the terminal. |
| Temperature characteristics | Tests at 202, -40(-25)3, 1052. Criteria: tan within limit, leakage current not more than 8 times specified value at -40. Impedance ratio Z-25/Z+20 and Z-40/Z+20 specified in table. |
| Load life test | Condition: 105C 2 with DC bias voltage plus rated ripple current for Table 1. Criteria: Leakage current satisfied, Capacitance Change within 25%, tan not more than 150% of specified value. No electrolyte leakage. |
| Shelf life test | Condition: Stored at 1052 for 1000+48/0 hours, then applied rated voltage with series resistor. Criteria: Leakage current satisfied, Capacitance Change within 25%, tan not more than 150% of specified value. No electrolyte leakage. |
| Surge test | Condition: 1000 cycles of charge (305s) and discharge (5 min 30s) with surge voltage. Criteria: Leakage current not more than specified value, Capacitance Change within 15%, tan not more than specified value. No electrolyte leakage. |
| Vibration test | Condition: 10Hz ~ 55Hz, 1.5mm peak to peak amplitude for 2 hours in 3 directions. Criteria: No intermittent contacts, open or short circuiting. No damage of tab terminals or electrodes. No mechanical damage, leakage or swelling. Markings legible. |
| Solderability test | Condition: Soldering temperature 2453, Dipping time 30.5s. Criteria: Minimum 95% of immersed surface coated. |
| Resistance to solder heat test | Condition: Solder bath at 2605 for 101s or 40010 for 1-0+1s. Criteria: Leakage current satisfied, Capacitance Change within 10%, tan not more than specified value. No electrolyte leakage. |
| Change of temperature test | Condition: 5 cycles of +20, -40(-25) (302 min), +105 (302 min). Criteria: Leakage current satisfied, tan not more than specified value. No electrolyte leakage. |
| Damp heat test | Condition: 90~95% RH at 402 for 5008 hours. Criteria: Leakage current satisfied, Capacitance Change within 20%, tan not more than 120% of specified value. No electrolyte leakage. |
| Vent test | Condition: Polarity reversed DC test with specified current based on diameter. Criteria: Vent operates with no dangerous conditions (flames, dispersion of pieces). |
| Maximum permissible (ripple current) | Maximum AC current at 120Hz and maximum operating temperature. Frequency multipliers provided for different frequencies. |
Environment-related Substances
Controlled substances include: Heavy metals (Cadmium, Lead, Mercury, Hexavalent chromium), Chlorinated organic compounds (PCB, PCN, PCT, SCCP), Brominated organic compounds (PBB, PBDE), Tributyltin compounds (TBT), Triphenyltin compounds (TPT), Asbestos, Specific azo compounds, Formaldehyde, Beryllium oxide, Beryllium copper, Specific phthalates, Hydrofluorocarbon (HFC), Perfluorocarbon (PFC), Perfluorooctane sulfonates (PFOS), Specific Benzotriazole.
2411271947_Man-Yue-Tech-EGF227M1EF12CB_C726192.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
