<
>
Specifications
Operating Temperature:
-45℃~+105℃
Lifetime:
5000hrs@105℃
Capacitance:
4.7uF
Height - Seated (Max):
11mm
Pin Spacing:
2mm
Voltage Rating:
50V
Diameter:
5mm
Tolerance:
±20%
Mfr. Part #:
EGT475M1HD11HB
Package:
Through Hole,D5xL11mm
Key Attributes
Model Number:
EGT475M1HD11HB
Product Description
Product Overview
The SAMXON GT Series Aluminum Electrolytic Capacitors are foil-type, polar capacitors designed for use in electronic equipment. They meet IEC60384 standards and are constructed with a single-ended type, featuring tinned CP wire leads, aluminum foil electrodes, a rubber seal, aluminum case, and a PET sleeve. These capacitors are suitable for general electronic applications requiring reliable performance.
Product Attributes
- Brand: SAMXON
- Series: GT Series
- Construction: Single ended type, foil type, polar
- Sleeve Material: PET
- Lead Material: Tinned CP wire (Pb Free)
- Case Material: Aluminum case
- Origin: MAN YUE ELECTRONICS COMPANY LIMITED
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap. tolerance | Temp. range () | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100kHz (mA rms) | Impedance at 20 100kHz (max) | Load lifetime (Hrs) | Dimension (mm) DL | F | d | H1 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EGT475M1HD11HB**P | 50 | 4.7 | -20%~+20% | -40~105 | 0.10 | 3 | 88 | 1.900 | 5000 | 5X11 | 2.0~2.5 | 0.5 | 3.5 |
General Characteristics
| Item | Specification |
|---|---|
| Standard atmospheric conditions | Ambient temperature: 15C to 35C, Relative humidity: 45% to 85%, Air Pressure: 86kPa to 106kPa |
| Measurement conditions | Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa |
| Rated voltage (WV) | 6.3, 10, 16, 25, 35, 50, 63, 100 V.DC |
| Surge voltage (SV) | 8, 13, 20, 32, 44, 63, 79, 125 V.DC |
| Nominal capacitance (Tolerance) measurement | Frequency: 120Hz12Hz, Voltage: Not more than 0.5Vrms, Temperature: 202 |
| Leakage current measurement | Series resistor: 1k10, Time: 2 minutes |
| tan measurement | Frequency: 120Hz12Hz, Voltage: Not more than 0.5Vrms, Temperature: 202 |
| Impedance measurement | Frequency: 100kHz, Temperature: 202, Measuring point: 2mm max from sealing rubber |
| Terminal strength (Tensile force) | 0.5mm and less: 5 N (0.51 kgf), Over 0.5mm to 0.8mm: 10 N (1.0 kgf) |
| Terminal strength (Bending force) | 0.5mm and less: 2.5 N (0.25 kgf), Over 0.5mm to 0.8mm: 5 N (0.51 kgf) |
| Load life test conditions | 105 2 C, DC bias voltage + rated ripple current, 5000+48/0 hours |
| Shelf life test conditions | 1052 for 1000+48/0 hours (no voltage applied) |
| Surge test cycles | 1000 cycles (Charge: 30 5s, Discharge: 5 min 30s) |
| Vibration test frequency range | 10Hz ~ 55Hz |
| Vibration test peak to peak amplitude | 1.5mm |
| Solderability test temperature | 2453C |
| Solderability test dipping time | 30.5s |
| Resistance to solder heat test temperature | 2605 for 101 seconds OR 40010 for 3 + 0 1 seconds |
| Change of temperature test cycles | 5 cycles (302 Minutes at -40/-25 and +105) |
| Damp heat test conditions | 90~95% RH at 402 for 500 8 hours |
| Vent test conditions (for products with vent) | DC test with reversed polarity, specific current applied based on diameter |
| Max permissible ripple current frequency multipliers | Refer to document for values at various frequencies and capacitance ranges. |
Application Guidelines Summary
- Capacitor parameters vary with temperature and frequency.
- Avoid reverse voltage, over voltage, and exceeding maximum ripple current.
- Use DC bipolar capacitors for circuits with changing or uncertain polarity.
- Standard capacitors are not suitable for repeating charge/discharge applications.
- Consider voltage imbalances when using capacitors in series and ripple current imbalances in parallel.
- Ensure proper mounting clearances for pressure relief vents.
- Avoid high voltage/current wiring near pressure relief vents.
- Capacitor sleeves are for identification and not electrical insulation.
- Handle capacitors carefully to avoid mechanical or electrical damage.
- Observe soldering temperature and time specifications.
- Avoid excessive stress on leads during insertion, soldering, and handling.
- Use appropriate cleaning solvents and drying methods.
- Avoid storing or using capacitors outside their rated environmental conditions.
- Emergency procedures for vent operation include immediate equipment shutdown.
- Recondition capacitors stored for long periods by applying rated voltage with a current limiting resistor.
- Dispose of capacitors by incineration after crushing or puncturing, or as solid waste, following local laws.
Environment-related Substances
Controlled substances list available, refer to the latest document "Environment-related Substances standard" (WI-HSPM-QA-072).
2411272252_Man-Yue-Tech-EGT475M1HD11HB_C2903583.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
