X-CON BRAND CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
This specification applies to conductive polymer aluminum solid capacitors used in electronic equipment.
Product Attributes
- Brand: X-CON
- Series: ULR
- Type: Conductive Polymer Aluminum Solid Capacitors
- Customer P/N: /
- Supplier: SAMXON ELECTRONIC COMPONENTS LIMITED
- Issued Date: 2014-05-26
- Version: 01
Technical Specifications
| Part Number System | Rated Voltage (WV) | Surge Voltage (SV) | Nominal Capacitance (F) | Capacitance Tolerance | Leakage Current (Max.) | Tangent of Loss Angle (tan) (Max.) | ESR (20) (Max.) | Operating Temperature Range | Load Life Test | Damp Heat Test |
|---|---|---|---|---|---|---|---|---|---|---|
| ULR 6.3V270F (6.3x6) | 6.3 V.DC | 7.2 V.DC | 270 | -20% ~ +20% (M) | See Table 3 | 0.10 (at 6.3V working voltage) | Less than initial limit (See Table 3) | -55C to 105C | 2000+48/0 hours at 105C with rated voltage | 100048 hours at 602, 90~95%RH |
Construction
Single-ended type with tinned copper or CP line terminals, aluminum foil anode and cathode, electrolyte paper, polymer electrolyte, and aluminum case sealed with end seal rubber.
Characteristics Measurement Conditions
Standard Atmospheric Conditions: Ambient temperature: 15C to 35C, Relative humidity: 45% to 75%, Air Pressure: 86kPa to 106kPa.
Measurement Conditions for Doubtful Results: Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa.
Detailed Test Criteria
Capacitance: Measured at 120Hz12Hz, 0.5Vrms, 202. Shall be within specified tolerance.
Leakage Current: Measured after 2 minutes with rated voltage applied through a 1k10 resistor. Remeasurement after voltage treatment (120 mins at 105) if exceeding Table 3 values.
Tangent of Loss Angle (tan): Measured under same conditions as Capacitance.
ESR: Measured at 100kHz to 300kHz, 202. Measuring point: 2mm max from sealing resin surface.
Temperature Characteristic: Impedance ratio (Z-55/Z20 1.25, Z105/Z20 1.25), Capacitance change (C/C 20 within 5% of step 1), tan ( value of item 4.4).
Load Life Test Criteria: Capacitance Change (20% of initial), tan (1.5 times of item 4.4), ESR (1.5 times of item 4.5), Leakage current ( value of item 4.3), Appearance (no notable changes).
Surge Test Criteria: Capacitance Change (20% of initial), tan (1.5 times of item 4.4), ESR (1.5 times of item 4.5), Leakage current ( value of item 4.3).
Damp Heat Test Criteria: Capacitance Change (20% of initial), tan (1.5 times of item 4.4), ESR (1.5 times of item 4.5), Leakage current ( value of item 4.3), Appearance (no notable changes).
Maximum Permissible Ripple Current: Max A.C current at 100kHz and max operating temperature. See Table 3. Frequency multipliers provided.
Rapid Change of Temperature Criteria: Capacitance change (10% of initial), tan ( value of item 4.4), Leakage current ( value of item 4.3 after voltage treatment).
Lead Strength Criteria: Leakage current ( value of item 4.3), Outward Appearance (no cutting and slack).
Product Dimensions, Impedance & Maximum Permissible Ripple Current
Refer to pages 13, 14, and 15 of the original specification for detailed information.
Application Guideline
Includes circuit design, voltage considerations, sudden charge/discharge restrictions, ripple current, leakage current, failure rate, capacitor insulation, and general precautions for using capacitors.
Mounting Precautions
Refer to page 15 of the original specification.
List of Environment-related Substances to be Controlled (Controlled Substances)
Refer to page 16 of the original specification.
2411220127_Man-Yue-Tech-ULR277M0JE06RR_C840160.pdf
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
