<
>
Specifications
Voltage Rating:
7.5V
Capacitance:
390uF
Lifetime:
2000hrs@105℃
Tolerance:
±20%
Pin Spacing:
2mm
Equivalent Series Resistance(ESR):
12mΩ@100kHz
Height - Seated (Max):
9mm
Operating Temperature:
-55℃~+105℃
Ripple Current:
3.1A@100kHz
Diameter:
5mm
Mfr. Part #:
ULR397V07D09RR
Package:
Through Hole,D5xL9mm
Key Attributes
Model Number:
ULR397V07D09RR
Product Description
Product Overview
The X-CON BRAND ULR Series Conductive Polymer Aluminum Solid Capacitors are designed for use in electronic equipment. These capacitors offer reliable performance and are constructed with a single-ended design featuring tinned copper or CP lead lines, aluminum terminals, and an aluminum case.
Product Attributes
- Brand: X-CON
- Category: CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
- Series: ULR
- Construction: Single ended type
- Materials: Tinned Copper Line or CP Line (Pb Free), Aluminum, Rubber, Aluminum Foil, Electrolyte paper (Manila Hemp), Aluminum Case
Technical Specifications
| Item | Specification | Condition | Criteria |
|---|---|---|---|
| Rated voltage (WV) | 7.5 V.DC | ||
| Surge voltage (SV) | 8.6 V.DC | ||
| Nominal capacitance (Tolerance) | 390F (-10% ~ +20%) | Measuring Frequency: 120Hz12Hz, Measuring Voltage: Not more than 0.5Vrms, Measuring Temperature: 202 | Shall be within the specified capacitance tolerance. |
| Leakage current | See Table 3 | After DC Voltage is applied through a 1k 10 resistor to reach rated voltage. Measured after 2 minutes. | Shall not exceed values of the following equation. Remeasure after voltage treatment (rated voltage for 120 minutes at 105) if leakage current exceeds Table 3 values. |
| Tangent of loss angle (tan) | 0.10 (max.) for 7.5V | Measuring Frequency: 120Hz12Hz, Measuring Voltage: Not more than 0.5Vrms, Measuring Temperature: 202 | |
| ESR | Less than the initial limit (See Table 3) | Measuring frequency: 100kHz to 300kHz; Measuring temperature: 202; Measuring point: 2mm max from the surface of a sealing resin on the lead wire. | (20) |
| Temperature characteristic | Z -55 / Z 20 1.25; Z105 / 20 1.25; C/C 20 Within 5%; tan Less than or equal to the value of item 4.4 | a. Impedance ratio at 100kHz; b. Capacitance change at 120Hz; c. tan at 120Hz. Steps: -55, 105, 20 | |
| Load life test | Capacitance Change: Within 20% of initial; tan: 1.5 times of item 4.4; ESR: 1.5 times of item 4.5; Leakage current: item 4.3; Appearance: No notable changes. | Stored at 105 2 C with rated voltage for 2000 +48/0 hours. | |
| Surge test | Capacitance Change: Within 20% of initial; tan: 1.5 times of item 4.4; ESR: 1.5 times of item 4.5; Leakage current: item 4.3 | Applied surge voltage through 1k resistor in series for 305 seconds, repeated 1000 times at 15~35. Left under normal humidity for 1-2 hours before measurement. | |
| Damp heat test | Capacitance Change: Within 20% of initial; tan: 1.5 times of item 4.4; ESR: 1.5 times of item 4.5; Leakage current: item 4.3; Appearance: No notable changes. | Exposed for 100048 hours in an atmosphere of 90~95%RH at 602. | |
| Maximum permissible ripple current | See Table 3 | Maximum A.C current at 100kHz and maximum operating temperature. Combined D.C voltage and peak A.C voltage shall not exceed rated voltage and shall not reverse voltage. | |
| Rapid change of temperature | Capacitance change: Within 10% of initial; tan: item 4.4; Leakage current: item 4.3 (after voltage treatment) | Applied voltage: without load. 5 cycles of -55 (30min), Room temp (15min), 105 (30min). Transition time 3 min. | |
| Lead strength (Lead pull) | Static load force applied axially away from body for 101 s. | d 0.5mm: 5N | |
| Lead strength (Lead bending) | Capacitor in vertical position, weight applied to one lead, rotated 900 to horizontal and back. Bends completed in 2~3 seconds. | d 0.5mm: 2.5N | |
| Lead strength (Performance) | Leakage current: item 4.3; Outward Appearance: No cutting and slack of lead terminals. | After a) or b) test. | |
| Resistance to vibration | Capacitance difference: Within 5% compared to initial value after exam. | Frequency: 10 to 55 Hz (1min interval/105510Hz); Amplitude: 0.75mm (Total excursion 1.5mm); Direction: X, Y, Z (3 axes); Duration: 2 hours/axial (Total 6 hours). | Capacitance value shall not show drastic change compared to the initial capacitance when measured within 30 minutes. |
2410121449_Man-Yue-Tech-ULR397V07D09RR_C840161.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
