<
>
Specifications
Voltage Rating:
6.3V
Capacitance:
1000uF
Lifetime:
2000hrs@105℃
Tolerance:
±20%
Pin Spacing:
3.5mm
Equivalent Series Resistance(ESR):
7mΩ@100kHz
Height - Seated (Max):
8mm
Operating Temperature:
-55℃~+105℃
Ripple Current:
6.1A@100kHz
Diameter:
8mm
Mfr. Part #:
ULR108M0JF08RR
Package:
Through Hole,D8xL8mm
Key Attributes
Model Number:
ULR108M0JF08RR
Product Description
X-CON BRAND CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
This specification applies to conductive polymer aluminum solid capacitors used in electronic equipment.
Product Attributes
- Brand: X-CON
- Category: CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
- Model: ULR 6.3V1000F (8x8)
- Version: 01
- Issued Date: 2020-09-08
Technical Specifications
| Item | Condition/Description | Performance/Criteria |
|---|---|---|
| Characteristics | Standard atmospheric conditions: Ambient temperature: 15C to 35C, Relative humidity: 45% to 75%, Air Pressure: 86kPa to 106kPa. Measurement conditions: Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa. | N/A |
| Operating temperature range: -55C to 105C | Continuous operation at rated voltage. | |
| Rated voltage (WV): 6.3 V.DC | Surge voltage (SV): 7.2 V.DC | |
| Nominal capacitance (Tolerance): Condition: Measuring Frequency: 120Hz12Hz, Measuring Voltage: 0.5Vrms, Measuring Temperature: 202 | Shall be within the specified capacitance tolerance. For 1000F, tolerance is -20% ~ +20% (Code "M"). | |
| Leakage current | Condition: Applied DC Voltage through a 1k 10 resistor to reach rated voltage. Measured after 2 minutes. Criteria: See Table 3 (not provided in source). If exceeding Table 3 values, remeasure after voltage treatment (rated voltage for 120 minutes at 20). | N/A (Refer to Table 3) |
| Tangent of loss angle (tan) | Condition: Measuring frequency: 120Hz, Measuring voltage: 0.5Vrms, Measuring temperature: 202. Criteria: For 6.3V, tan (max.) is 0.10. | 0.10 (for 6.3V) |
| ESR (Equivalent Series Resistance) | Condition: Measuring frequency: 100kHz to 300kHz, Measuring temperature: 202, Measuring point: 2mm max from sealing resin. Criteria: Less than the initial limit (See Table 3). | N/A (Refer to Table 3) |
| Temperature characteristic | Condition: 1. Impedance ratio at 100kHz (-55/20 and 105/20). 2. Capacitance change at 120Hz (C/C 20). 3. tan at 120Hz. Steps: Measure at 202, -553, then back to 202, then 1052, then back to 202. | Z-55 / 20 1.25 Z105 / 20 1.25 C/C 20 Within 5% of step 1 tan value of item 4.4 |
| Load life test | Condition: Stored at 105 2 C with rated voltage for 2000 +48/0 hours. | Capacitance Change: Within 20% of initial tan: 1.5 times of item 4.4 ESR: 1.5 times of item 4.5 Leakage current: value of item 4.3 Appearance: No notable changes. |
| Surge test | Condition: Applied surge voltage with a (100 50)/CR (k) resistor. 1000 cycles of 30 5s charge, 5 min 30s discharge. Test temperature: 15~35. | Capacitance Change: Within 20% of initial tan: 1.5 times of item 4.4 ESR: 1.5 times of item 4.5 Leakage current: value of item 4.3 |
| Damp heat test | Condition: Exposed for 100048 hours in 90~95%RH at 602. | Capacitance Change: Within 20% of initial tan: 1.5 times of item 4.4 ESR: 1.5 times of item 4.5 Leakage current: value of item 4.3 Appearance: No notable changes. |
| Maximum permissible ripple current | Condition: Maximum A.C current at 100kHz and maximum operating temperature. Combined DC and peak AC voltage shall not exceed rated voltage and no reverse voltage. Frequency Multipliers provided for different frequencies. | See Table 3 (not provided in source). |
| Rapid change of temperature | Condition: 5 cycles of temperature change (-553 to 1052) with 3 min or less transition time. Applied voltage: without load. | Capacitance change: Within 10% of initial tan: value of item 4.4 Leakage current: value of item 4.3 (after voltage treatment) |
| Lead strength | Condition: a) Lead pull strength (static load for 101 s). b) Lead bending (slow rotation). Criteria: For lead diameter (0.5 < d 0.8 mm): Pull force 10N, Bending force 5N. | Leakage current: value of item 4.3 Outward Appearance: No cutting and slack of lead terminals. |
| Resistance to vibration | Condition: Frequency: 10 to 55 Hz (1min interval), Amplitude: 0.75mm (Total excursion 1.5mm), Direction: X, Y, Z (3 axes), Duration: 2 hours/axial (Total 6 hours). | Capacitance value shall not show drastic change. Capacitance difference within 5% compared to initial value after the exam. |
Part Number System
ULR 108 M 0J F 08 RR
- Capacitance (2.1): Code 108 = 1000 F
- Rated voltage (2.2): Code 0J = 6.3 V.DC
- Type (2.3): Code RR = Bulk
- Capacitance tolerance (2.4): "M" = -20% ~ +20%
- Diameter (2.5): Code F = 8 mm
- Case length (2.6): 08 = 8 mm
Construction
Single ended type. Components include Lead Line (Tinned Copper Line or CP Line (Pb Free)), Terminal (Aluminum), Sealing Material (Rubber), Al-Foil (+) (Aluminum), Al-Foil (-) (Aluminum), Case (Aluminum), Electrolyte paper (Manila Hemp).
Application Guideline
Covers circuit design, voltage, sudden charge and discharge restrictions, ripple current, leakage current, failure rate, capacitor insulation, and general precautions for using capacitors.
Long Term Storage
Refer to section 8.
Mounting Precautions
Refer to section 9.
Environment-related Substances
Refer to section 10 for List of Environment-related Substances to be Controlled (Controlled Substances).
2410121457_Man-Yue-Tech-ULR108M0JF08RR_C840077.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
