<
>
Specifications
Normal temperature Frequency Tolerance:
±30ppm
Frequency Stability:
±20ppm
Operating Temperature:
-20℃~+70℃
Load Capacitance:
20pF
Frequency:
12MHz
Mfr. Part #:
KBD120002030
Package:
HC-49S-SMD
Key Attributes
Model Number:
KBD120002030
Product Description
HC-49USSMD/12.000 MHZ
20PF/30ppm
KBD120002030
(Kaiyuexiang)
HC-49USSMD/12.000 MHZ
| Holder Type | HC-49USSMD | |
| Mode of Vibration | AT CUT | |
| Oscillation Mode | FUND S&A | |
| Test Facilities | KH-1240 | |
| Storage Temperature | -40 TO +85 | |
| Driver Level | 100W | |
| Normal Frequency | 12.000 MHz | |
| Frequency Tolerance (252) | 30ppm | |
| Temperature Stability | 20ppm | |
| Operating Temperature Range | -20 TO +70 | |
| Load Capacitance | 20 PF | |
| Motional Capacitance | 3PF MAX | |
| Shunt Capacitance | ||
| Effective Series Resistance | 80 MAX | |
| Insulation Resistance | 500M OHMS MIN at DC 100V | |
| Solderability | 95% coverage by using 90/10 sold at 245 for 5 sec. Dipping after immersion in ALPHA 611 flux for 5 sec. | |
| (Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour.) | ||
| Shock | Electrical characteristics shall be satisfied after dropping three times from the height of 50 cm onto Hard wooden board. | |
| Vibration | Vibration Frequency: 1055Hz, Repeated Period: 12min, Full Amplitude: 1.5mm PP, Direction: X.Y.Z, Time: 2hours/each direction | Electrical characteristics shall be satisfied after supplying following Vibration. |
| Strength of Terminals/Lead-Wires - Pulling | 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. No visual damages after test. | Body of specimen shall be fixed. |
| Strength of Terminals/Lead-Wires - Bending | 90degree bending shall be given, being supplied 225gs tension weight. Then straightened gradually. Same bending and straightening to the opposite direction. No visual damages after test. | Body of specimen shall be fixed. (Refer to Fig-1) |
| Sealing Tightness | No observation of gas bubble after specimen put in hot water at +90+95 for 5 min. | |
| Soldering Dip | Terminals/lead-wires shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. Soldering portion shall be covered in over 90% of terminals/lead-wires dipped. | (After applying ROSIN flux) |
| Solder Heating | Electrical characteristics shall be satisfied after dipping terminals/lead-wires into solder melted tank at +35010 for 3 sec. Dipping depth shall be 2mm from edge of terminals/lead-wires. | |
| (Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour.) | ||
| Humidity | Electrical characteristics shall be satisfied after letting it alone at 602 in humidity of 9095% for 250 hours. | |
| Storage in Low Temperature | Electrical characteristics shall be satisfied after letting it alone at -302 for 250 hours. | |
| Storage in High Temperature | Electrical characteristics shall be satisfied after letting it alone at +852 for 250 hours. | |
| Temperature Cycle | Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min. (Refer to Fig-2) |
2409272302_KYX-KBD120002030_C18209141.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
