<
>
Specifications
Normal temperature Frequency Tolerance:
±20ppm
Frequency Stability:
±20ppm
Operating Temperature:
-20℃~+70℃
Load Capacitance:
20pF
Equivalent Series Resistance(ESR):
60Ω
Frequency:
16MHz
Mfr. Part #:
KSD160002020
Package:
HC-49S-SMD
Key Attributes
Model Number:
KSD160002020
Product Description
Product Overview
This document specifies the characteristics and performance of the HC-49USSMD/16.000 MHZ Quartz Crystal Resonator manufactured by Shenzhen Kaiyuexiang Electronics Co., Ltd. It is designed for applications requiring precise frequency control.
Product Attributes
- Brand: (Kaiyuexiang)
- Origin: Shenzhen, China
- Product Name: (Quartz Crystal Resonator)
- Product Model: HC-49USSMD/16.000 MHZ
- Original Model: KSD160002020
Technical Specifications
| Parameter | Value | Unit | Notes |
| 1. GENERAL | |||
| HOLDER TYPE | HC-49USSMD | ||
| MODE OF VIBRATION | AT CUT | FUND S&A KH-1240 | |
| OSCILLATION MODE | FUND | ||
| STORAGE TEMPERATURE | -40 to +85 | ||
| DRIVER LEVEL | 100 | W | |
| 2. ELECTRICAL PARAMETER | |||
| NORMAL FREQUENCY | 16.000 | MHz | |
| FREQUENCY TOLERANCE252 | 20 | ppm | |
| TEMPERATURE STABILITY | 20 | ppm | |
| OPERATING TEMPERATURE RANGE | -20 to +70 | ||
| LOAD CAPACITANCE | 20 | PF | |
| MOTIONAL CAPACITANCE | 5 | PF MAX | |
| SHUNT CAPACITANCE | |||
| EFFECTIVE SERIES RESISTANCE | 60 | MAX | |
| INSULATION RESISTANCE | 500 | M OHMS MIN | AT DC 100V |
| 3. MECHANICAL PARAMETER | |||
| SOLDERABILITY | 95% COVERAGE BY USING 90/10 SOLD AT 245 FOR 5 SEC. | DIPPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC. | |
| MECHANICAL ENDURANCE | |||
| SHOCK | Electrical characteristics shall be satisfied after dropping three times from the height of 50 cm onto Hard wooden board. | ||
| VIBRATION | Electrical characteristics shall be satisfied after supplying following Vibration. | ||
| - VIBRATION FREQUENCY | 1055 | Hz | |
| - REPEATED PERIOD | 12 | min | |
| - FULL CYCLE | 1.5 | mm PP | |
| - DIRECTION | X.Y.Z | ||
| - TIME | 2 hours/each direction | ||
| STRENGTH OF TERMINALS/LEADWIRES - PULLING | Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. After above test, there is no observation of any visual damages on the specimen. | ||
| STRENGTH OF TERMINALS/LEADWIRES - BENDING | Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight. After that, terminals/lead-wires shall be straightened gradually. Then the same bending and straightening shall be supplied to the opposite direction in the same axial. After above test, there is no observation of any visual damages on the specimen. | (Refer to Fig-1) | |
| SEALING TIGHTNESS | There is no observation of gas bubble after specimen put in hot water at +90+95 for 5 min. | ||
| SOLDERING DIP | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped. | ||
| SOLDER HEATING | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires. | ||
| ENVIRONMENTAL ENDURANCE | |||
| HUMIDITY | Electrical characteristics shall be satisfied after letting it alone at 602 in humidity of 9095% for 250 hours. | ||
| STORAGE IN LOW TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at -302 for 250 hours. | ||
| STORAGE IN HIGH TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at +852 for 250 hours. | ||
| TEMPERATURE CYCLE | Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min (Refer to Fig-2). | ||
2409272302_KYX-KSD160002020_C18213244.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
