<
>
Specifications
Normal temperature Frequency Tolerance:
-5ppm~+15ppm
Frequency Stability:
±20ppm
Operating Temperature:
-20℃~+70℃
Load Capacitance:
13.5pF
Frequency:
12MHz
Mfr. Part #:
KBD12000135515
Package:
HC-49S-SMD
Key Attributes
Model Number:
KBD12000135515
Product Description
HC-49USSMD/12.000 MHZ
KBD12000135515
- (Kaiyuexiang)
| GENERAL | |||
| Holder Type | HC-49USSMD | ||
| Mode of Vibration | AT CUT | ||
| Oscillation Mode | FUND S&A | ||
| Test Facilities | KH-1240 | ||
| Storage Temperature | -40 to +85 | ||
| Driver Level | 100 | W | |
| ELECTRICAL PARAMETER | |||
| Normal Frequency | 12.000 | MHz | |
| Frequency Tolerance (252) | -5 to +15 | ppm | |
| Temperature Stability | 20 | ppm | |
| Operating Temperature Range | -20 to +70 | ||
| Load Capacitance | 13.5 | PF | |
| Motional Capacitance | 3 | PF MAX | |
| Shunt Capacitance | |||
| Effective Series Resistance | 80 | MAX | |
| Insulation Resistance | 500 | M OHMS MIN | AT DC 100V |
| MECHANICAL PARAMETER | |||
| Solderability | 95% Coverage by using 90/10 Sold at 245 for 5 sec. Dipping after immersion in ALPHA 611 FLUX for 5 sec. |
| Shock | Electrical characteristics shall be satisfied after dropping three times from the height of 50 cm onto Hard wooden board. | 50 cm 3 |
| Vibration | Electrical characteristics shall be satisfied after supplying following Vibration. (1)VIBRATION FREQUENCY 1055Hz (2)REPEATED PERIOD 12min (3)FULL CYCLE 1.5mm PP (4)DIRECTION X.Y.Z (5)TIME 2hours/each direction | |
| Strength of Terminals/Lead-Wires (Pulling) | Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. After above test a), there is no observation of any visual damages on the specimen. | 900g /30 |
| Strength of Terminals/Lead-Wires (Bending) | Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight. After that, terminals/lead-wires shall be straightened gradually. Then the same bending and straightening shall be supplied to the opposite direction in the same axial. After above test a), there is no observation of any visual damages on the specimen. | 90o 225g 90 o |
| Sealing Tightness | There is no observation of gas bubble after specimen put in hot water at +90+95for 5 min. | +90+955 |
| Soldering Dip | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped. | +23053 2mm90 |
| Solder Heating | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires. | +350103-4 2mm |
| Humidity | Electrical characteristics shall be satisfied after letting it alone at 602in humidity of 9095% for 250 hours. | 6029095%250 |
| Storage in Low Temperature | Electrical characteristics shall be satisfied after letting it alone at -302for 250 hours. | -302250 |
| Storage in High Temperature | Electrical characteristics shall be satisfied after letting it alone at +852for 250 hours. | +852250 |
| Temperature Cycle | Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min (Refer to Fig-2). | 3 1/2 |
TEL0755-89315823 / 89315866
FAX0755-89315223
www.kaiyuexiang.com
2409272302_KYX-KBD12000135515_C18209143.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
