<
>
Specifications
Normal temperature Frequency Tolerance:
±30ppm
Frequency Stability:
±20ppm
Operating Temperature:
-20℃~+70℃
Load Capacitance:
20pF
Equivalent Series Resistance(ESR):
60Ω
Frequency:
16MHz
Mfr. Part #:
KSD160002030
Package:
HC-49S-SMD
Key Attributes
Model Number:
KSD160002030
Product Description
HC-49USSMD/16.000 MHZ
20PF/30ppm
KSD160002030
TEL0755-89315823 89315866 FAX0755-89315223
www.kaiyuexiang.com
| 1. GENERAL | ||
| HOLDER TYPE | HC-49USSMD | |
| MODE OF VIBRATION | AT CUT | FUND |
| OSCILLATION MODE | S&A | KH-1240 |
| TEST FACILITIES | ||
| STORAGE TEMPERATURE | -40TO +85 | |
| DRIVER LEVEL | 100W | |
| 2. ELECTRICAL PARAMETER | ||
| NORMAL FREQUENCY | 16.000 MHz | |
| FREQUENCY TOLERANCE252 | 30ppm | |
| TEMPERATURE STABILITY | 20ppm | |
| OPERATING TEMPERATURE RANGE | -20TO + 70 | |
| LOAD CAPACITANCE | 20 PF | |
| MOTIONAL CAPACITANE | 5PF MAX | |
| SHUNT CAPACITANCE | 60MAX | |
| EFFECTIVE SERIES RESISTANCE | 500M OHMS MIN AT DC 100V | |
| INSULATION RESISTANCE | 95%COVERAGE BY USING 90/10 SOLD AT 245FOR 5 SEC. DIPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC. | |
| 3. MECHANICAL PARAMETER | ||
| SOLDERABILITY | ||
| MECHANICAL ENDURANCE | ||
| SHOCK | Electrical characteristics shall be satisfied after dropping three time from the height of 50 cm onto Hard wooden board . | 50 cm 3 |
| VIBRATION | Electrical characteristics shall be satisfied after supplying following Vibration . | |
| VIBRATION FREQUENCY | 1055Hz | |
| REPEATED PERIOD | 12min | |
| FULL CYCLE | 1.5mm PP | |
| DIRECTION | X.Y.Z | |
| TIME | 2hours/each direction | 2 / |
| STRENGTH OF TERMINALS/LEADWIRES | ||
| PULLING | a)Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec . b)After above test a), there is no observation of any visual damages on the specimen. | a)900g /30 b)a) |
| BENDING | a)Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight . After that, terminals/lead-wires shall be straightened gradually . Then the same bending and straightening shall be supplied to the opposite direction in the same axial . (Refer to Fig-1) b)After above test a), there is no observation of any visual damages on the specimen . | a)90o 225g 90 o 1 b)a) |
| SEALING TIGHTNESS | There is no observation of gas bubble after specimen put in hot water at +90+95for 5 min . | +90+955 |
| SOLDERING DIP | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec . Dipping depth shall be 2mm from the bottom of specimens body . (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped . | +23053 2mm 90 |
| SOLDER HEATING | Terminals/lead-wires of specimen shall be dipped into solder melted tank at +1 +35010 for 3 sec . Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires . | +350103-4 2mm |
| ENVIRONMENTAL ENDURANCE | ||
| HUMIDITY | Electrical characteristics shall be satisfied after letting it alone at 602in humidity of 9095% for 250 hours . | 6029095%250 |
| STORAGE IN LOW TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at -302for 250 hours . | -302250 |
| STORAGE IN HIGH TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at +852for 250 hours . | +852250 |
| TEMPERATURE CYCLE | Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles) . Temperature shift from low to high, high to low shall be done in 1/min (Refer to Fig-2) . | 3 1/2 |
2409272302_KYX-KSD160002030_C18213242.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
