<
>
Specifications
Normal temperature Frequency Tolerance:
±20ppm
Load Capacitance:
20pF
Frequency:
6MHz
Mfr. Part #:
KBD060002020
Package:
HC-49S-SMD
Key Attributes
Model Number:
KBD060002020
Product Description
HC-49USSMD/6.000 MHZ
20PF/20ppm
KBD00002020
- 0755-89315823, 89315866
- 0755-89315223
- www.kaiyuexiang.com
| 1. GENERAL | |||
| HOLDER TYPE | HC-49USSMD | ||
| MODE OF VIBRATION | AT CUT | FUND | |
| OSCILLATION MODE | S&A | KH-1240 | |
| TEST FACILITIES | |||
| STORAGE TEMPERATURE | -40TO +85 | ||
| DRIVER LEVEL | 100W | ||
| 2. ELECTRICAL PARAMETER | |||
| NORMAL FREQUENCY | 6.000 | MHz | |
| FREQUENCY TOLERANCE252 | 20 | ppm | |
| TEMPERATURE STABILITY | 20 | ppm | |
| OPERATING TEMPERATURE RANGE | -20TO + 70 | ||
| LOAD CAPACITANCE | 20 | PF | |
| MOTIONAL CAPACITANE | 3 | PF MAX | |
| SHUNT CAPACITANCE | |||
| EFFECTIVE SERIES RESISTANCE | 250 | MAX | |
| INSULATION RESISTANCE | 500 | M OHMS MIN | AT DC 100V |
| 3. MECHANICAL PARAMETER | |||
| SOLDERABILITY | 95%COVERAGE BY USING 90/10 SOLD AT 245FOR 5 SEC. DIPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC. | ||
(MECHANICAL ENDURANCE)
Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour. 1
- 1 SHOCK (): Electrical characteristics shall be satisfied after dropping three time from the height of 50 cm onto Hard wooden board. 50 cm 3
- 2 VIBRATION (): Electrical characteristics shall be satisfied after supplying following Vibration.
- (1)VIBRATION FREQUENCY: 1055Hz
- (2)REPEATED PERIOD: 12min
- (3)FULL CYCLE: 1.5mm PP
- (4)DIRECTION: X.Y.Z
- (5)TIME: 2hours/each direction (2 /)
- 3 STRENGTH OF TERMINALS/LEADWIRES ():
- -1 PULLING (): a) Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. 900g /30 b) After above test a), there is no observation of any visual damages on the specimen. a)
- -2 BENDING (): a) Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight. After that, terminals/lead-wires shall be straightened gradually. Then the same bending and straightening shall be supplied to the opposite direction in the same axial. (Refer to Fig-1) 90o 225g 90 o 1 b) After above test a), there is no observation of any visual damages on the specimen. a)
- 4 SEALING TIGHTNESS (): There is no observation of gas bubble after specimen put in hot water at +90+95for 5 min. +90+955
- 5 SOLDERING DIP (): Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped. +23053 2mm 90
- 6 SOLDER HEATING (): Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires. +350103-4 2mm
(ENVIRONMENTAL ENDURANCE)
Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour. 1
- 1 HUMIDITY (): Electrical characteristics shall be satisfied after letting it alone at 602in humidity of 9095% for 250 hours. 6029095%250
- 2 STORAGE IN LOW TEMPERATURE (): Electrical characteristics shall be satisfied after letting it alone at -302for 250 hours. -302250
- 3 STORAGE IN HIGH TEMPERATURE (): Electrical characteristics shall be satisfied after letting it alone at +852for 250 hours. +852250
- 4 TEMPERATURE CYCLE (): Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min (Refer to Fig-2). 3 1/2
:
:
:
2409272303_KYX-KBD060002020_C19076796.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
