<
>
Specifications
Normal temperature Frequency Tolerance:
±20ppm
Frequency Stability:
±20ppm
Operating Temperature:
-20℃~+70℃
Load Capacitance:
20pF
Equivalent Series Resistance(ESR):
60Ω
Frequency:
16MHz
Mfr. Part #:
KBD160002020
Package:
HC-49S-SMD
Key Attributes
Model Number:
KBD160002020
Product Description
49USSMD/16.000MHZ
KBD160002020
20PF/20ppm
- (Kaiyuexiang)
- TEL0755-89315823 89315866, FAX0755-89315223
- www.kaiyuexiang.com
| / | ||
|---|---|---|
| 1. GENERAL | ||
| HOLDER TYPE | 49USSMD | |
| MODE OF VIBRATION | AT CUT | |
| OSCILLATION MODE | FUND S&A | |
| TEST FACILITIES | KH-1240 | |
| STORAGE TEMPERATURE | -40 TO +85 | |
| DRIVER LEVEL | 100W | |
| 2. ELECTRICAL PARAMETER | ||
| NORMAL FREQUENCY | 16.000MHz | |
| FREQUENCY TOLERANCE (252) | 20ppm | |
| TEMPERATURE STABILITY | 20ppm | |
| OPERATING TEMPERATURE RANGE | -20 TO +70 | |
| LOAD CAPACITANCE | 20PF | |
| MOTIONAL CAPACITANE | 7PF | MAX |
| SHUNT CAPACITANCE | ||
| EFFECTIVE SERIES RESISTANCE | 40 | MAX |
| INSULATION RESISTANCE | 500M OHMS MIN | AT DC 100V |
| 3. MECHANICAL PARAMETER | ||
| SOLDERABILITY | 95% COVERAGE BY USING 90/10 SOLD AT 245 FOR 5 SEC. DIPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC. | |
| MECHANICAL ENDURANCE | ||
| SHOCK | Electrical characteristics shall be satisfied after dropping three time from the height of 50 cm onto Hard wooden board. | |
| VIBRATION | Electrical characteristics shall be satisfied after supplying following Vibration. (VIBRATION FREQUENCY: 1055Hz, REPEATED PERIOD: 12min, FULL CYCLE: 1.5mm PP, DIRECTION: X.Y.Z, TIME: 2hours/each direction) | |
| STRENGTH OF TERMINALS/LEADWIRES (PULLING) | 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. No visual damages. | |
| STRENGTH OF TERMINALS/LEADWIRES (BENDING) | 90degree bending with 225gs tension weight. No visual damages. | |
| SEALING TIGHTNESS | No observation of gas bubble after specimen put in hot water at +90+95 for 5 min. | |
| SOLDERING DIP | Terminals/lead-wires dipped into solder melted tank at +2305 for 3sec. Dipping depth 2mm from the bottom of specimens body. Soldering portion shall be covered in over 90% of terminals/lead-wires dipped. | |
| SOLDER HEATING | Terminals/lead-wires dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied. Dipping depth 2mm from edge of terminals/lead-wires. | |
| ENVIRONMENTAL ENDURANCE | ||
| HUMIDITY | Electrical characteristics shall be satisfied after letting it alone at 602 in humidity of 9095% for 250 hours. | |
| STORAGE IN LOW TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at -302 for 250 hours. | |
| STORAGE IN HIGH TEMPERATURE | Electrical characteristics shall be satisfied after letting it alone at +852 for 250 hours. | |
| TEMPERATURE CYCLE | Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min. | |
2409272303_KYX-KBD160002020_C2835968.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
