<
>
Specifications
Voltage Rating:
200V
Capacitance:
2.2nF
Temperature Coefficient:
NP0
Tolerance:
±5%
Mfr. Part #:
C0805N222J201TCF
Package:
0805
Key Attributes
Model Number:
C0805N222J201TCF
Product Description
Product Overview
The IHHEC Multilayer Ceramic Chip Capacitors (MLCC) HVC-021-2005 series are designed for electric equipment with voltage ratings from 100V to 1.5 KV. These MLCCs support Lead-Free wave and reflow soldering, maintaining their electrical characteristics and reliability. The product is compliant with RoHS and HF standards.
Product Attributes
- Brand: IHHEC (a trademark of Holy Stone Enterprise Co., Ltd)
- Certifications: RoHS & HF compliant
Technical Specifications
| Item | Specification | Test Condition |
| Visual | No abnormal exterior appearance | Visual inspection |
| Dimension | See Page 2 | Visual inspection |
| Insulation Resistance | 10,000Mmin. | V500V, Rated Voltage Charge Time60sec. Is applied less than 50mA current. |
| Capacitance | Class NPO Within The Specified Tolerance | |
| Q Factor | Class NPO More Than 30pF : Q 1000 | |
| Withstanding Voltage | No dielectric breakdown or mechanical breakdown | V500V : 200% Rated Voltage Voltage ramp up rate500v/sec for 1~5 sec. charge/discharge Current is less than 50mA. Withstanding voltage testing requires immersion of the element in a isolation fluid prevent arcing on the chip surface, at voltage over 1000Vdc. |
| Temperature Capacitance Coefficient | Class : [C2-C1/C1(T2-T1)] 100% T1: Standard temperature (25 ) T2: Test temperature C1:Capacitance at standard temperature(25 ) C2: Capacitance at test temperature (T2) | NPO -55~+125 30 ppm/ |
| Adhesive Strength of Termination | No indication of peeling shall occur on the terminal electrode. Pull force shall be applied for 10 1 second. | 0603----5N( 0.5 Kgf) 0603----10N(1.0 Kgf) |
| Resistance to Flexure of Substrate | Appearance: No mechanical damage shall occur. Bending shall be applied to the 1.0 mm with 1.0 mm/sec. The duration of the applied forces shall be 5 1sec | Capacitance Change: NPO 5.0% Class Capacitance Frequency Voltage NPO 1KHz10% 1.00.2Vrms Perform a heat temperature at 1505 for 30min. then place room temp. for 242hr. R230 C Meter 451mm 451mm Bending Limit Nf |
| Solderability | More than 90% of the terminal surface is to be soldered newly, so metal part does not come out or dissolve . | Solder Temperature : 245 5 Dip Time : 5 0.5 sec. Immersing Speed : 2510% mm/s Solder : Lead Free Solder Flux :Rosin Preheat : At 80~120 for 10~30sec. |
| Resistance To Soldering Heat | Appearance: No mechanical damage shall occur. Class capacitor shall be set for 484 hours at room temperature after one hour heat treatment at 150 +0/-10 before initial measure. | Preheat : At 150 10 For 60~120sec. Dip : Solder Temperature of 260 5 Dip Time : 10 1sec. Immersing Speed : 2510% mm/s Flux :Rosin Measure at room temperature after cooling for Class: 24 2 Hours Capacitance Characteristic Cap. Change Class (NPO) Within 2.5% or 0.25pFwhichever is larger of initial value Q Class To satisfy the specified initial value Insulation Resistance To satisfy the specified initial value Withstand Voltage To satisfy the specified initial value |
| Temperature Cycle | Appearance: No mechanical damage shall occur. Class capacitor shall be set for 48 4 hours at room temperature after one hour heat treatment at 150 +0/-10 before initial measure. Capacitor shall be subjected to five cycles of the temperature cycle as following: | Measure at room temperature after cooling for Class :24 2Hrs Solder the capacitor on P.C. board shown in Fig 2. before testing. Capacitance Characteristic Cap. Change Class (NPO) Within 2.5% or 0.25pFwhichever is larger of initial value Q Class To satisfy the specified initial value Insulation Resistance To satisfy the specified initial value |
| Humidity | Appearance: No mechanical damage shall occur. Class capacitor shall be set for 48 4 hours at room temperature after one hour heat treatment at 150+0/-10 before initial measure. | Temperature : 40 2 Relative Humidity : 90 ~ 95%RH Test Time : 500 +12/-0Hr Measure at room temperature after cooling for Class : 24 2Hrs Solder the capacitor on P.C. board shown in Fig 2. before testing. Capacitance Characteristic Cap. Change Class (NPO) Within 5.0% or 0.5pF whichever is larger of initial value Q Class More Than 30pF : Q 350 Insulation Resistance 1,000Mmin. Step Temp.() Time(min) 1 Min Rated Temp. +0/-3 30 2 25 3 3 Max Rated Temp. +3/-0 30 4 25 3 |
| High Temperature Load (Life Test) | Appearance: No mechanical damage shall occur. Class capacitors applied DC voltage (following table) is applied for one hour at maximum operation temperature 3 then shall be set for 484 hours at room temperature and the initial measurement shall be conducted. Applied Voltage : 150%Rated Voltage Test Time : 1000 +12/-0Hr Current Applied : 50 mA Max. | Measure at room temperature after cooling for Class: 24 2 Hours Capacitance Characteristic Cap. Change Class (NPO) Within 3.0% or 0.3pFwhichever is larger Q Class More Than 30pF : Q 350 Insulation Resistance 1,000Mmin. |
| Vibration | Appearance: No mechanical damage shall occur. Solder the capacitor on P.C. Board shown in Fig 2. before testing. Vibrate the capacitor with amplitude of 1.5mm P-P changing the frequencies from 10Hz to 55Hz and back to 10Hz in about 1 min. Repeat this for 2 hours each in 3perpendicular directions. | Capacitance Characteristic Cap. Change Class (NPO) Within 2.5% or 0.25pFwhichever is larger Q Class To satisfy the specified initial value Insulation Resistance To satisfy the specified initial value |
2410121653_IHHEC-C0805N222J201TCF_C2991898.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
