<
>
Specifications
Type:
Wirewound Resistor
Resistance:
5.1Ω
Voltage-Supply(Max):
-
Power(Watts):
1W
Temperature Coefficient:
±350ppm/℃
Tolerance:
±5%
Mfr. Part #:
RXF-1W-5.1R-J-T52
Package:
Through Hole,D5xL12mm
Key Attributes
Model Number:
RXF-1W-5.1R-J-T52
Product Description
Product Overview
The RXF series from Dongguan Hongda Electronic Technology Co., Ltd. are resistors designed for a wide range of electronic equipment. They offer good surge resistance, excellent fusing consistency, and a compact size for easy installation, ensuring safety and reliability. These resistors are widely used in electronic devices such as light sources, switching power supplies, chargers, and home appliances.
Product Attributes
- Brand: RXF Series
- Manufacturer: Dongguan Hongda Electronic Technology Co., Ltd.
- Origin: China
- Certifications: VDE (Certificate No.: 40036858), UL/CUL (Certificate No.: E359590), CQC (Certificate No.: 0.5W-CQC13001095211, 1W-CQC13001095213, 2W-CQC13001095221)
Technical Specifications
Dimensions and Lead Lengths
| Model | Rated Power (W) | Dimensions (mm) Dmax. x Lmax. | Lead Allowable Length* (mm) H1 | Diameter d0.05 |
|---|---|---|---|---|
| RXF 0.25, 0.5S, 1WX | 3.0 | 7.0 | 6070 | 0.380.45 |
| RXF 0.5, 1S, 2WX | 4.0 | 10.0 | 6090 | 0.430.60 |
| RXF 1, 2S, 3WX | 5.0 | 12.0 | 6070 | 0.540.72 |
| RXF 2, 3S | 6.0 | 16.0 | 6080 | 0.600.72 |
Electrical Specifications
| Model | Rated Power (W) | Resistance Range () | Resistance Tolerance (%) | Insulation Voltage (V) (DC or AC peak) | Component Limit Voltage (V) |
|---|---|---|---|---|---|
| RXF 0.25, 0.5S, 1X | - | 0.22-300 | 5, 10 | 250 | 200 |
| RXF 0.5, 1S, 2X | - | - | - | 250 | 250 |
| RXF 1, 2S, 3X | - | - | - | 350 | 350 |
| RXF 2, 3S | - | 0.22-47 | - | 500 | 350 |
General Data
| Parameter | Specification |
|---|---|
| Nominal Resistance Tolerance | 5%, 10% |
| Climatic Category | 55/155/21 |
| Low Air Pressure | 8.5kPa |
| Stability Grade | 5% |
| Resistance Change Limit (Long-term) | (5%R+0.1) |
| Resistance Change Limit (Short-term) | (1%R+0.05) |
| Temperature Coefficient | Standard Type: 350 ppm; Semi-fusing, Explosion-proof, High Lightning Surge Type: 35001500 ppm |
| Rated Current | I(A) = P(W) / R() |
| Power Derating | Rated power is maximum continuous operation at 70. Derate according to the curve above 70. (See Figure 2) |
| Fusing Characteristic | Defined as significant increase in resistance when subjected to specified overload, causing current to drop below 1/50 of initial test current. Fusing time is the duration from overload application to fusing. |
| Fusing Time Requirements (Standard and High Lightning Surge Types) | See Table 3-1 for overload multiples and fusing times. Fusing time can be customized. |
| Fusing Time Requirements (Explosion-proof Types) | See Table 3-2. |
| Fusing Time Requirements (Semi-fusing Types) | See Table 3-3. |
| Surge Impact Performance | Test requires repeated switching (2s on, 2s off) for 100 cycles without open circuit. (See Figure 3) |
| Capacitor C Selection | Based on customer requirements; default 10uF if not specified. |
| Resistor R Selection | Based on circuit usage, calculated as internal resistance. Resistor power rating 20W, power factor 0.8. For resistors below 10W, typically use 20W, 5.1K (5%). |
Main Test Items, Methods, and Performance Requirements
| No. | Test Item | Test Method | Performance Requirement |
|---|---|---|---|
| 1 | Resistance | Measured by resistance error sorter. | Resistance value within nominal value and allowable tolerance. |
| 2 | Short-time Overload | Apply 2.5 times rated voltage for 5s, recover for 1-2h, measure resistance, calculate change rate. | Resistance Change: R (2%R + 0.05) |
| 3 | Solderability | Dip lead ends in solder pot (2605) for 20.5s, depth 2+0/-0.5mm from body. Observe coverage. | Over 90% surface coverage in circumferential direction on dipped part. |
| 4 | Withstand Voltage | Place resistor in metal 'V' groove, apply specified insulation voltage between leads and groove for 60s. | No visible damage, clear marking; no breakdown or arcing. |
| 5 | Solder Heat Resistance | Measure resistance before test. Dip lead ends in solder pot (35010) for 3.50.5s, depth 2+0/-0.5mm from body. Recover for 1h, measure resistance, calculate change rate. | Resistance Change: R (1%R + 0.05) |
| 6 | Rapid Temperature Change | Cycle: Low temp (-553) (30min), room temp (2-3min), high temp (1553) (30min), room temp (2-3min). Repeat 5 cycles. Recover 1-2h, measure resistance, calculate change rate. | Resistance Change: R (1%R + 0.05) |
| 7 | Endurance | Place in constant temperature oven (703), apply rated DC voltage. Cycle: 1.5h on, 0.5h off for 1000h. Recover 1-4h, measure resistance, calculate change rate. | Resistance Change: R (5%R + 0.1) |
| 8 | Lead Strength | Tensile: 10N for 10s. Bending: Apply 5N load, tilt body ~90 in (2-3)s. Repeat bending in opposite direction. | Resistance Change: R (1%R + 0.05) |
| 9 | Vibration | Resistor body 61mm from mounting point. Frequency 10-500Hz, amplitude 0.75mm or acceleration 98m/s (whichever is smaller). Duration 2h each on Z, X, Y axes (total 6h). Cycle: 1min (10-55-10Hz). Measure resistance, calculate change rate. | 1) Appearance: No mechanical damage. 2) Resistance Change: R (1%R + 0.05) |
| 10 | Climatic Sequence | Dry heat, cyclic damp heat (Db), cold, low pressure, cyclic damp heat (Db), DC load. | Resistance Change: R (5%R + 0.1). Insulation Resistance: 100M. |
| 11 | Accidental Overload | Install sample in single-layer silk screen cylinder (253mm from body). Apply 5, 10, 16 times rated power overload for 5min or until open circuit. | Silk screen cylinder does not ignite. |
Taped Packaging Specifications
| Taped Specification | Dimensions (mm) U x W | Pitch P (mm) | L1-L2 | T | Z | R | t | T2 |
|---|---|---|---|---|---|---|---|---|
| T26 | 381 x 260.5 | 50.5 | 0.5 | 60.1 | 1 | 0 | 3.2 | 1.5 |
| T52 | 642 x 521 | - | 1 | - | - | - | - | - |
| T63 | 752 x 631 | 100.5 | 1.2 | - | - | - | - | - |
| T72 | 842 x 722 | 50.5 | 1.2 | - | - | - | - | - |
Sleeve Product Specifications
| Type | Dimensions (mm) H1 | H11.5 | H21.5 | hh (15%) | h12 | h22 |
|---|---|---|---|---|---|---|
| TA Type | 70 | 20 | 20 | 50 | 10 | 10 |
| TB Type | 80 | 5 | 25 | 40 | 10 | 30 |
Molded Product Specifications
| Type | Dimensions (mm) P1.0 | H1 | h0.5 |
|---|---|---|---|
| n Type | 5 | 3.5 | 8 |
| B Type | 5 | 3.5 | 8 |
| L Type | 12.5 | 4.5 | 14.5 |
| L Type | - | 5.5 | - |
Model Specification Naming Convention
| Component | Description |
|---|---|
| RXF | Series Name |
| Rated Power | 0.25w, 0.5w, 1w, 2w, 3w |
| Resistance Tolerance | J: 5%, K: 10%, M: 20% |
| Nominal Resistance | E24 Series (See color code diagram) |
| Type | S: Miniaturized, X: Ultra-miniaturized |
Color Code Markings
| Color | 1st Digit | 2nd Digit | 3rd Digit | Multiplier | Tolerance |
|---|---|---|---|---|---|
| Black | 0 | 0 | 0 | 10 (1) | - |
| Brown | 1 | 1 | 1 | 10 (10) | 1% |
| Red | 2 | 2 | 2 | 10 (100) | 2% |
| Orange | 3 | 3 | 3 | 10 (1k) | - |
| Yellow | 4 | 4 | 4 | 10 (10k) | - |
| Green | 5 | 5 | 5 | 10 (100k) | 0.5% |
| Blue | 6 | 6 | 6 | 10 (1M) | 0.25% |
| Violet | 7 | 7 | 7 | 10 (10M) | 0.1% |
| Gray | 8 | 8 | 8 | 10 (100M) | - |
| White | 9 | 9 | 9 | 10 (1G) | - |
| Gold | - | - | - | 10 (0.1) | 5% |
| Silver | - | - | - | 10 (0.01) | 10% |
| Plain | - | - | - | - | 20% |
Packaging
- Inner Box Packaging: Taped 1K/box
- Outer Box Packaging: Not specified
2304140030_Hongda-RXF-1W-5-1R-J-T52_C2149613.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
