<
>
Specifications
Voltage Rating:
50V
Tolerance:
±20%
Temperature Coefficient:
-
Power(Watts):
30mW
Number of Turns:
-
Resistance:
1kΩ
Mfr. Part #:
RA1010L-5V-0814-A1K-000
Package:
Through Hole
Key Attributes
Model Number:
RA1010L-5V-0814-A1K-000
Product Description
Product Overview
10mm ROTARY POTENTIOMETER from Dong Guan PinZan Electronics Science and technology Co.,Ltd. Designed for various applications, this potentiometer offers reliable performance with specific mechanical and electrical characteristics.
Product Attributes
- Brand: PinZan
- Origin: Dong Guan, China
Technical Specifications
| Item | Specifications | Notes |
| 1. Environment | ||
| Operating temperature range | -10+70C | |
| Storage temperature range | -25+75C | |
| Test conditions | Standard atmospheric conditions: Ambient temperature:535C, Relative humidity : 4585%, Air pressure: 860 mbar to 1060 mbar | Unless otherwise specified |
| Reference conditions: Ambient temperature:202C, Relative humidity : 6070%, Air pressure: 860 mbar to 1060 mbar | If there is any doubt about the results, measurements shall be made within the following limit | |
| 2. Mechanical characteristics | ||
| Total rotational angle | 27010 | |
| Rotational torgue | 5~100gf.cm | |
| Rotational speed | 60/1 sec. | |
| Push and pull strength of knob | 0.5kgf shall be applied to the knob in the axial direction for 3 sec. No abnormality in electric characteristics and operating feeling. | |
| Knob wobble | 0.6xL/30 mm p-p max. (L:The knob diameter) | A momentary load of 100 gf-cm shall be applied at the point 2 mm from the tip of the knob in a direction perpendicular to the axis of knob |
| Shaft stopper strength | 0.6Kgf-cm max. | |
| 3. Electrical characteristics | ||
| Nominal total resistance | B1K20% | Terminal 1-3 |
| Resistance law (Taper) | Refer to Taper graph shown | |
| Insulation resistance | 100Mmin. | at DC100 volts |
| Dielectric strength | Apply AC100 V for 1 min. between individual terminals and case/shaft without damage to parts,arcing or breakdown etc. | |
| End resistance | 20max. | Between terminal 1-2 and 2-3 |
| Noise | 100mV max. | |
| Life(no load) | 5,000 cycles. | No load life test speed of 1 cycle( CW270CCW270)/6 |
| Maximum operating voltage | AC 50V. | |
| Power rating | 0.03W | |
| Tracking error | 4db (-40db~0db) | Tracking is measured by applying 1kHz,2V to terminals 1 &3 of each control and getting out voltage of terminals 1 & 2 of each control. |
| 4. Common Specification of Lead-Free Soldering for potentiometers | ||
| Manual Soldering | Max 350C, within 3 seconds | |
| Automated/Semi-Automated Soldering | Solder dipping within 4 seconds at 260C or below. Flux of 0.82 specific gravity, applied by foam fluxer. Preheating time not exceeding 2 minutes, soldering surface temperature within 100C. | This specification is not recommended for and applicable in reflow soldering. For rotary potentiometer with plastic shaft which have center detent or multiple detents, the shaft should be settled in relevant detent position prior to soldering process. Solder dipping or solder smearing must not be carried out more than 1 time. |
2410121458_G-Switch-RA1010L-5V-0814-A1K-000_C22750562.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
