<
>
Specifications
Mfr. Part #:
MPP155J2GA080B200ZR
Package:
Through Hole,P=20mm
Key Attributes
Model Number:
MPP155J2GA080B200ZR
Product Description
Product Overview
The CBB21/MPP series metallized polypropylene film capacitors are designed for electronic equipment with epoxy encapsulation. These capacitors feature a non-inductive winding structure with metallized polypropylene film and are suitable for DC blocking, coupling, decoupling, filtering, bypassing, and other high-frequency, DC, AC, and pulse circuits. They offer good self-healing properties, low loss, and low internal temperature rise, with a flame-retardant epoxy resin powder coating.
Product Attributes
- Brand: Dongguan Chengxi Electronics Co., Ltd.
- Product Type: CBB21/MPP type metallized polypropylene film capacitor (impregnated type)
- Construction: Non-inductive winding structure
- Encapsulation: Flame-retardant epoxy resin powder coating
- Lead Wire: Tinned copper wire or tinned copper-clad steel wire
- Environmental Compliance: RoHS, REACH, Halogen-free (if required)
Technical Specifications
| Model/Part Number | Capacitance (uF) | Tolerance (%) | Rated Voltage (VDC) | Dissipation Factor (DF) (1KHz) | Dimensions (mm) (L x H x T) | Pitch (P) (mm) |
|---|---|---|---|---|---|---|
| MPP155J2GA080B200ZR | 1.5 | 5% | 400 | 0.1% | 21.6 x 14.9 x 7.8 | 20.0 |
General Electrical Characteristics
| Parameter | Specification | Test Conditions |
|---|---|---|
| Climate Category | 40/105/21 | - |
| Operating Temperature Range | -40 to +105 | (Voltage derating of 1.25% / for +85 to +105) |
| Rated Temperature | 85 | - |
| Capacitance Range | 0.001F to 6.8F | - |
| Capacitance Tolerance | 5% (J), 10% (K) | - |
| Rated Voltage (VDC) | 100, 160, 250, 400, 630, 1000, 1250, 1600, 2000 | - |
| Dissipation Factor (DF) | 0.0010 | (1kHz, 20) |
| Insulation Resistance | 30,000M (for C0.33uF) 10000M*uF (for C>0.33uF) | (100VDC, 60 seconds) |
| Dielectric Strength | 1.6 UR(VDC) | 5 seconds |
Maximum Pulse Rise Rate (dV/dt)
If the actual working voltage (U) is lower than the rated voltage (UR), the capacitor can operate at a higher dV/dt. The allowable dV/dt value should be multiplied by UR/U.
| dV/dt (V/s) | UR (VDC) | P=7.5mm | P=10.0mm | P=15.0mm | P=22.5mm | P=27.5mm |
|---|---|---|---|---|---|---|
| 100/160 | 130 | 110 | 100 | 70 | 50 | |
| 250 | 240 | 220 | 200 | 120 | 100 | |
| 400 | 450 | 350 | 300 | 180 | 150 | |
| 630 | 550 | 420 | 400 | 250 | 180 | |
| 1000/1250 | 2300 | 1950 | 975 | 600 | 300 | |
| 1600 | 6000 | 4500 | 2400 | - | - | |
| 2000 | 8000 | 4500 | - | - | - |
Product Structure and Main Materials
| No. | Main Material | Description | Remark |
|---|---|---|---|
| 1 | Metallized Polypropylene Film | MPPZAH | -/- |
| 2 | Sprayed Layer | Zinc-tin alloy wire | -/- |
| 3 | Lead Wire | Tinned copper-clad steel wire | -/- |
| 4 | Outer Encapsulation Material | Epoxy resin powder | Flame retardant UL94V-0 |
| 5 | Inner Protective Material | Epoxy resin | - |
Note: All raw materials and finished products comply with RoHS environmental requirements.
Packaging Specifications
| Item | Dimensions (L*W*H) |
|---|---|
| Inner Box | 34.5 x 23.5 x 24.5 cm |
| Outer Box | 49 x 36 x 27 cm |
Packaging Details:
- Box contents include: Manufacturer part number, number of packages and quantity per package, Lot No.
- Capacitors are packaged in transparent PVC bags for moisture and dust protection.
- RoHS environmental mark.
- Other customer marking requirements.
Storage Conditions
- Prolonged exposure to air may degrade lead wire soldering performance.
- Avoid high temperature and high humidity environments.
- Temperature: Max 35
- Relative Humidity: Max 80%
- Storage Time: Maximum 12 months from the production date marked on the packaging bag.
Environmental Characteristics
- Complies with RoHS requirements.
- Complies with REACH requirements.
- Complies with Halogen-free requirements (if specified).
Product Electrical Characteristics and Test Conditions
General Test Conditions: Ambient temperature: 1535, Relative humidity: 25%75%
Strict Test Conditions: Ambient temperature: 202, Relative humidity: 60%70%
Reliability Test Items
| No. | Item | Characteristic | Test Method | Criteria |
|---|---|---|---|---|
| 1 | Terminal Strength | Tensile Strength | Load: 10N, Time: 10 seconds | No visible mechanical damage |
| Bending Strength | Wire diameter: 0.6 & 0.8mm, Force: 5N, 90 2 times | - | ||
| 2 | Solderability | Tinning rate of leads | Flux temperature: 2455, Immersion time: 2.50.5 seconds | 95% |
| 3 | Soldering Heat Resistance | Appearance | Solder temperature: 2605, Immersion time: 101 seconds, Recovery time: 1-2 hours | No visible damage |
| DF Increase | - | 0.004 (C1.0F, 10kHz) 0.004 (C>1.0F, 1kHz) | ||
| Capacitance Change | - | C/C 3% | ||
| 4 | Rapid Change of Temperature | Appearance | A=-40, B=+105, 5 cycles, Duration: 30 min | No visible damage |
| Vibration | Amplitude 0.75mm or acceleration 98m/s, Frequency 10-500Hz, 3 directions, 2h each, total 6h | No visible damage | ||
| Shock | 4000 times, acceleration 390m/s, pulse duration: 6ms | No visible damage | ||
| Final Measurement | Appearance | - | No visible damage | |
| Capacitance Change | - | C/C 5% | ||
| DF Increase | - | 0.004 | ||
| Insulation Resistance | - | IR/IR 50% | ||
| 5 | Climatic Sequence | Appearance | Dry Heat: +105, 16h Cyclic Damp Heat (Test Db, 1st cycle) Cold: -40, 2h Low Pressure: 8.5kPa, 1h Cyclic Damp Heat (Test Db, remaining cycles) | No visible damage |
| Capacitance Change | - | C/C 5% | ||
| DF Increase | - | 0.005 | ||
| Insulation Resistance | - | IR/IR 50% | ||
| 6 | Damp Heat, Steady State | Appearance | Relative Humidity: 90-95%RH, Temperature: 402, No load, Duration: 21 days, Recovery time: 1-2 hours | No visible damage |
| Capacitance Change | - | C/C 5% | ||
| DF Increase | - | 0.002 (C1.0F, 10kHz) 0.004 (C>1.0F, 1kHz) | ||
| Insulation Resistance | - | IR/IR 50% | ||
| 7 | Endurance | Appearance | T=85, 1000 hours, Applied Voltage: 1.25UR | No visible damage |
| Capacitance Change | - | C/C 8% | ||
| DF Increase | - | 0.004 | ||
| Insulation Resistance | - | IR/IR 50% | ||
| 8 | Characteristics Dependent on Temperature | Capacitance measurement at points b, d, f | Static method, capacitor held sequentially at each temperature: a.(202), b.(-403), d.(20 2), f.(1052), g.(202) | At lower category temperature -40: 0 (Cb-Cd)/Cd +3% At upper category temperature 105: -4.0% (Cf-Cd)/Cd 0 |
| 9 | Charge/Discharge | Capacitance Change | Charge/discharge cycles: 10,000 Charging time: 0.5s Discharging time: 0.5s Charging voltage: Rated voltage UR Charging resistance: 220/CR () Discharging resistance: 10/CR or 20 (whichever is larger) CR: Rated capacitance (uF) | C/C 5% |
| DF Increase | - | 0.005 (10KHz, CR1.0uF) 0.005 (1KHz, CR>1.0uF) | ||
| Insulation Resistance | - | IR/IR 50% |
Usage Rules
- Usage Range: Do not exceed the upper category temperature. Avoid overload. Do not exceed maximum pulse current.
- Operation Precautions: Avoid repeated squeezing at the lead wire root. Be cautious of lead wire tips.
- Soldering: Solder heat can transfer to the capacitor core through lead wires and encapsulation. Be mindful of potential damage from high temperatures and prolonged soldering.
- Wave Soldering: TP 110 for 120 seconds; Ts 120 for 45 seconds. For P7.5mm, T4mm, wave soldering time < 4 seconds.
- Soldering Iron: Tip temperature not exceeding 350, welding time not exceeding 3 seconds.
- Lead film capacitors are not suitable for reflow soldering.
Ts: Maximum temperature the capacitor body can withstand during wave soldering.
Tp: Maximum preheating temperature the capacitor body can withstand.
Maximum Effective Voltage and Frequency Curve Diagram
Note: The curve diagram shows typical values tested under conditions of sinusoidal voltage, ambient temperature 85, and capacitor internal temperature rise T=10.
Product Electrical Characteristic Diagrams
(Diagrams not provided in text)
2512241555_DGCX-MPP155J2GA080B200ZR_C53224148.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
