<
>
Specifications
Voltage Rating:
10V
Tolerance:
±20%
Power(Watts):
200mW
Resistance:
50kΩ
Mfr. Part #:
C2043N-CE10B5.0-W503-0P0
Package:
Through Hole,P=3.75mm
Key Attributes
Model Number:
C2043N-CE10B5.0-W503-0P0
Product Description
Product Overview
The C2043N is a slide potentiometer designed for consumer products, offering precise control with a nominal total resistance of 50K 20%. It operates within a wide temperature range and features reliable electrical and mechanical characteristics for consistent performance.
Product Attributes
- Model: C2043N
- Type: Slide Potentiometer
- Origin: Dongguan Changtaier Electronics Co., Ltd.
Technical Specifications
| Item | Conditions | Specifications |
|---|---|---|
| 1 GENERAL | ||
| Scope | Model C2043N type, mainly used for consumer products | |
| Operating temperature range | -10~60 | |
| Storage temperature range | -10~70 | |
| Test conditions | Standard atmospheric conditions: Ambient temperature:5~35 Relative humidity:45~85% Air pressure:86~106kpa Reference conditions: Ambient temperature:202 Relative humidity:60~70% Air pressure:86~106kpa | |
| 2 ELECTRICAL CHARACTERISTICS | ||
| Nominal total resistance and tolerance | Resistance between terminals 1 and 3 | 50K20% |
| Resistance law | W Taper (Refer to the attached) | |
| Power rating | Max continuous full load operation at max voltage between terminals 1 and 3. (Graph for power rating vs. ambient temperature denoted) | 0.2W |
| Rated voltage | E = PR/R; P: Rated power, R: Nominal total resistance | 200V AC (Max Operation Voltage 10V DC) |
| Residual resistance | R1,2; R2,3 | 20; 30 |
| Slide noise | Apply DC 20V between terminals 1-3 (rated voltage 20V, apply by rated voltage) | 68mVp-p |
| Insulation resistance | Apply voltage of DC 500V between individual terminals and frame for 1 minute. | 50M |
| Dielectric strength | Between individual terminals and frame | 500V AC for 1 minute. (Trip current: 2mA) |
| 3 Mechanical characteristics | ||
| Total travel slide | Effective slide travel | 200.5mm |
| Sliding force | Standard atmospheric conditions, Sliding speed: 1 Cycles/3s | 10~80gf |
| Number of Detents | Without Detent, 1C (Center Detent), Other | |
| Click slip out | Standard atmospheric conditions, Sliding speed: 20mm/sec | 20~110gf |
| Stop strength | Torsion moment load of 3Kgf.cm applied to the shaft for 5sec at both ends (after fixation) | Electrical characteristics shall be satisfied. |
| Lever wobble | Without damage such as bad sliding and braking or play in the lever. | |
| Thrust and tensile lever | Static load of 5kgf.cm applied to the lever in the lever directions for 10 sec. | Electrical characteristics shall be satisfied. |
| Terminal strength | 0.5kgf static force applied along the terminal position for 10 sec (after fixation) | Electrical characteristics shall be satisfied. |
| 4 ENDURANCE CHARACTERISTICS | ||
| Solder ability | Terminals immersed into solder bath at 2605C for 30.5s. 75% minimum of surface covered. | |
| Resistance to heat (soldering) | Preheating: Substrate surface temperature within 100C in one minute. Wave soldering: Bit temperature 3505C, Application time 5 1 sec. | Change in total resistance: 5%. No case deformation or terminal loosening. Electrical characteristics satisfied. |
| Resistance to heat | 1208h in a thermostatic chamber at 702C. Measured after maintaining at standard atmospheric conditions for 1h. | Change in total resistance: 20%. |
| Resistance to cold | 1204h in a thermostatic chamber at -253C. Measured after removing surface moisture and maintaining at standard atmospheric conditions for 1h. | Change in total resistance: 20%. |
| Damp heat | 1204h in a thermostatic chamber at 402C, 90% to 95% RH. Measured after removing surface moisture and maintaining at standard atmospheric conditions for 1h. | Change in total resistance: +35%~-5%. Insulation resistance: 50M. Noise: 150mV p-p. |
| Change of temperature | 5 successive temperature cycles. Measured after removing surface moisture and maintaining at standard atmospheric conditions for 1h. | Change in total resistance: 30%. Insulation resistance: 100M. Dielectric strength: Without damage, arcing or breakdown. |
| Endurance | Moving contact rotated from one end stop to the other and returned to original position (effective angle >90%). 600 cycles/hour. Total 10000200 cycles. | Change in total resistance: specified value15%. Rotational noise: 150mVp-p. Rotational torque shall not deviate from previously specified value. Residual resistance R1~2: 40, R2~3: 60. |
2410121318_CTR-C2043N-CE10B5-0-W503-0P0_C18213449.pdf
Request A Quote
Please Use Our Online Inquiry Contact Form Below If You Have Any Questions, Our Team Will Get Back To You As Soon As Possible
